Altera Cyclone V Скачать руководство пользователя страница 578

Страница: 578 / 1077

Description

Event

Data read lookup to the L2 cache. Subsequently results
in a hit or miss.

DRREQ

Data write hit in the L2 cache.

DWHIT

Data write lookup to the L2 cache. Subsequently
results in a hit or miss.

DWREQ

Data write lookup to the L2 cache with write-through
attribute. Subsequently results in a hit or miss.

DWTREQ

Prefetch hint allocated into the L2 cache.

EPFALLOC

Prefetch hint hits in the L2 cache.

EPFHIT

Prefetch hint received by slave port S0.

EPFRCVDS0

Prefetch hint received by slave port S1.

EPFRCVDS1

Allocation of a prefetch generated by L2 cache
controller into the L2 cache.

IPFALLOC

Instruction read hit in the L2 cache.

IRHIT

Instruction read lookup to the L2 cache. Subsequently
results in a hit or miss.

IRREQ

Secure privileged non-invasive debug enable.

SPNIDEN

Speculative read confirmed in slave port S0.

SRCONFS0

Speculative read confirmed in slave port S1.

SRCONFS1

Speculative read received by slave port S0.

SRRCVDS0

Speculative read received by slave port S1.

SRRCVDS1

Allocation into the L2 cache caused by a write, with
write-allocate attribute, miss.

For more information about the built-in L2 event monitoring capability, refer to “Implementation details”
in the

Functional Overview

chapter of the

CoreLink Level 2 Cache Controller L2C-310 Technical Reference

Manual

, available on the ARM website (infocenter.arm.com).

In addition, the L2 cache events can be captured and timestamped using dedicated debugging circuitry.

For more information about L2 event capture, refer to the

Debug

chapter of the Cortex-A9 MPCore Technical

Reference Manual, available on the ARM website (infocenter.arm.com).

Related Information

ARM Infocenter (www.infocenter.arm.com)

Cortex-A9 Microprocessor Unit Subsystem

Altera Corporation

Send Feedback

cv_54006

L2 Cache Event Monitoring

6-32

2013.12.30

Содержание Cyclone V






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Cyclone V

Отзывы:

Altera Cyclone V, Руководство по эксплуатации устройства, Страница: 578 / 1077

Результаты поиска

Содержание Cyclone V

Отзывы: