manualshive.com logo in svg

Altera Cyclone V, Руководство по эксплуатации устройства, Страница: 1031 / 1077

Поделиться
Скачать
Altera Cyclone V Скачать руководство пользователя страница 1031

Table 28-3: FPGA-to-HPS SDRAM Interfaces and Clocks

Associated Clock Interface

(1)

Description

Interface Name

f2h_sdram0_clock

SDRAM AXI or Avalon-MM port 0

f2h_sdram0_data

f2h_sdram1_clock

SDRAM AXI or Avalon-MM port 1

f2h_sdram1_data

f2h_sdram2_clock

SDRAM AXI or Avalon-MM port 2

f2h_sdram2_data

f2h_sdram3_clock

SDRAM AXI or Avalon-MM port 3

f2h_sdram3_data

f2h_sdram4_clock

SDRAM AXI or Avalon-MM port 4

f2h_sdram4_data

f2h_sdram5_clock

SDRAM AXI or Avalon-MM port 5

f2h_sdram5_data

The FPGA-to-HPS SDRAM interface is a configurable interface to the multi-port SDRAM controller.

The total data width of all interfaces is limited to a maximum of 256 bits in the read direction and 256 bits
in the write direction. The interface is implemented as four 64-bit read ports and four 64-bit write ports. As
a result, the minimum data width used by the interface is 64 bits, regardless of the number or type of interfaces.

You can configure this interface the following ways:

• AXI-3 or Avalon-MM protocol
• Number of interfaces
• Data width of interfaces

The FPGA-to-HPS SDRAM interface supports six command ports, allowing up to six Avalon-MM interfaces
or three bidirectional AXI interfaces.

Each command port is available either to implement a read or write command port for AXI, or to form part
of an Avalon-MM interface.

You can use a mix of Avalon-MM and AXI interfaces, limited by the number of command/data ports
available. Some AXI features are not present in Avalon-MM interfaces.

This interface has an address width of 32 bits. To access existing Avalon-MM/AXI masters, you can use the
Altera Address Span Extender.

Related Information

•

Clocks

on page 28-5

•

Features of the SD/MMC Controller

on page 11-1

For more information about available combinations of interfaces and ports, refer to the

SDRAM Controller

Subsystem

chapter.

•

HPS Component Interfaces

on page 28-1

For information about the address span extender, refer to “Using the Address Span Extender Component”
in the

Instantiating the HPS Component

chapter.

HPS Component Interfaces

Altera Corporation

Send Feedback

cv_54028

FPGA-to-HPS SDRAM Interface

28-4

2013.12.30

Содержание Cyclone V






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов