Altera Cyclone V страница 571 Скачать руководство пользователя | Manualshive

Страница: 571 / 1077

background image

The operating modes are programmable through accesses to the control and status registers in the ACP ID
mapper, available via the level 4 peripheral bus connection. At reset time, the ACP ID mapper defaults to
dynamic ID mapping for all output IDs except ID 2, which resets to a fixed mapping for the Debug Access
Port (DAP) input ID.

Related Information

Cortex-A9 MPU Subsystem with L3 Interconnect

on page 6-2

ID Intended Usage

summarizes the expected usage of the 3-bit output IDs, and their settings at reset.

Table 6-4: ID Intended Usage

Intended Use

Reset State

Output ID

Dynamic mapping only

Dynamic

7

Fixed or dynamic, programmed
by software.

Dynamic

6

5

4

3

Assigned to the input ID of the
DAP at reset. After reset, can be
either fixed or dynamic,
programmed by software.

Fixed at 0x001 (DAP)

2

Not used by the ACP ID Mapper

—

1

0

AXI User Sideband Override

For masters that cannot drive the AXI user sideband signal of incoming transactions, the ACP ID mapper
can control overriding this signal. The ACP ID mapper can also control which 1 GB coherent window into
memory is accessed by masters of the L3 interconnect. Each fixed mapping can be assigned a different user
sideband signal and memory window to allow specific settings for different masters. All dynamic mappings
share a common user sideband signal and memory window setting.

Transaction Capabilities

At any one time, the ACP ID mapper can accept and issue up to 15 transactions per ID mapping. Read and
write ID mappings are managed in separate lists, allowing more unique input IDs to be remapped at any
given time. If a master issues a series of reads and writes with the same input ID, there are no ordering
restrictions.

Because there are only six output IDs available, there can be no more than six read and six write transactions
with unique IDs in progress at any one time. The write acceptance of the ACP slave is five transactions, and
the read acceptance is 13 transactions. Only four coherent read transactions per ID mapping can be
outstanding at one time.

Altera Corporation

Cortex-A9 Microprocessor Unit Subsystem

Send Feedback

6-25

ID Intended Usage

cv_54006
2013.12.30

«
...
569
570
571
572
573
...
»

Содержание Cyclone V






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Cyclone V

ShareCenter Pulse DNS-320

Бренд: D-Link Страницы: 2

Бренд: D-Link Страницы: 4

Бренд: NEC Страницы: 10

Бренд: NEC Страницы: 8

IntelliJack NJ200

Бренд: 3Com Страницы: 4

Бренд: Barco Страницы: 100

Бренд: Hama Страницы: 4

DR-4100P Series

Бренд: Idis Страницы: 30

Бренд: Jetter Страницы: 35

Бренд: Yaesu Страницы: 2

Бренд: Vonets Страницы: 8

Procont LMC-008-IO

Бренд: janitza Страницы: 28

Oresund EFC102200

Бренд: Bridgeworks Страницы: 84

Бренд: Renesas Страницы: 76

Бренд: ADTRAN Страницы: 20

Бренд: ICP DAS USA Страницы: 8

JNLH61S-6C Series

Бренд: JETWAY Страницы: 36

593/25, 593/45, 593/TB, RS-422, RS-485

Бренд: Patton electronics Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды