Altera Cyclone V страница 803 Скачать руководство пользователя | Manualshive

Страница: 803 / 1077

background image

Faulting Completing

A DMA channel thread is waiting for the AXI master interface to signal that the outstanding load or store
transactions are complete. After the transactions complete, the thread moves to the Faulting state.

Faulting

The thread is stalled indefinitely. The thread moves to the Stopped state when you use the

DBGCMD

register

to instruct the DMAC to execute

DMAKILL

for that thread.

Killing

A DMA channel thread is waiting for the AXI master interface to signal that the outstanding load or store
transactions are complete. After the transactions complete, the thread moves to the Stopped state.

Completing

A DMA channel thread is waiting for the AXI master interface to signal that the outstanding load or store
transactions are complete. After the transactions complete, the thread moves to the Stopped state.

Related Information

Updating DMA Channel Control Registers During a DMA Cycle

on page 16-24

Error Checking and Correction

Error Checking and Correction (ECC) block provides outputs to notify the system manager when single-bit
correctable errors are detected

The SRAM local memory buffer is 64 by 512 bits, providing 4096 bytes of memory. The buffer provides
error checking and correction (ECC) capability. The ECC block is integrated around a memory wrapper,
and provides the following features:

• Output to notify the system manager when single-bit correctable errors are detected and corrected
• Output to notify the system manager when double-bit uncorrectable errors are detected
• Provision for the injection of single-bit and double-bit errors for test purposes

The ECC is disabled by default. For information on using the ECC feature, refer to the ECC chapter in the
Cyclone VDevice handbook

Initializing the DMAC

The DMAC provides several memory-mapped control signals that initialize its operating state when it exits
from reset. The DMAC does not automatically begin executing code when it exits from reset. The system
manager controls the following memory-mapped control signals.

Related Information

System Manager

on page 14-1

How to Set the Security State of the DMA Manager

The

boot_manager_ns

signal is the only method to set the security state of the DMA manager.

When the DMAC exits from reset, it reads the status of the

boot_manager_ns

signal and sets the security

of the DMA manager.

Altera Corporation

DMA Controller

Send Feedback

16-7

Error Checking and Correction

cv_54016
2013.12.30

«
...
801
802
803
804
805
...
»

Содержание Cyclone V






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Cyclone V

Бренд: TC Electronic Страницы: 2

IntelliJack NJ200

Бренд: 3Com Страницы: 4

SmartMedia Adapter PC Card REX-SMA01F

Бренд: Ratoc Systems Страницы: 75

Бренд: T&D Страницы: 122

Бренд: Salto Страницы: 2

Бренд: IBASE Technology Страницы: 71

Бренд: Net to Net Technologies Страницы: 4

PoleVault System A/V Source Inputs

Бренд: Extron electronics Страницы: 4

Бренд: EMCIS Страницы: 14

Бренд: Kanguru Страницы: 13

Бренд: Giacomini Страницы: 2

Бренд: XJTAG Страницы: 9

Бренд: Xilinx Страницы: 8

FireWire 800 ExpressCard 34

Бренд: LaCie Страницы: 24

Бренд: Xinje Страницы: 76

Бренд: Juniper Страницы: 6

Бренд: Wavtech Страницы: 8

Бренд: Paradyne Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды