Altera Cyclone V страница 327 Скачать руководство пользователя | Manualshive

Страница: 327 / 1077

background image

synchronization code groups that the link must receive to acquire synchronization and a specific number
of erroneous code groups that it must receive to fall out of synchronization.

In PCIe configurations, the word aligner in automatic synchronization state machine mode automatically
selects the word alignment pattern length and pattern as specified by each protocol. The synchronization
state machine parameters are fixed for PCIe configurations as specified by the respective protocol.

Table 1-22: Word Aligner in Synchronization State Machine Modes for a PCIe Configuration

PCIe

Mode

4

Number of valid synchronization code groups or ordered sets received to achieve synchro-
nization

17

Number of erroneous code groups received to lose synchronization

16

Number of continuous good code groups received to reduce the error count by one

After deassertion of the

reset_rx_digital

signal in automatic synchronization state machine mode,

the word aligner starts looking for the word alignment pattern or synchronization code groups in the received
data stream. When the programmed number of valid synchronization code groups or ordered sets is received,
the

rx_syncstatus

status bit is driven high to indicate that synchronization is acquired. The

rx_syncstatus

status bit is constantly driven high until the programmed number of erroneous code

groups is received without receiving intermediate good groups; after which

rx_syncstatus

is driven

low. The word aligner indicates loss of synchronization (

rx_syncstatus

remains low) until the

programmed number of valid synchronization code groups are received again.

Word Aligner Operations in Deterministic Latency State Machine Mode

In deterministic latency state machine mode, word alignment is achieved by performing a clock-slip in the
deserializer until the deserialized data coming into the receiver PCS is word-aligned. The deterministic
latency state machine controls the clock-slip process in the deserializer after the word aligner has found the
alignment pattern and has identified the word boundary. Deterministic latency state machine mode offers
a reduced latency uncertainty in the word alignment operation for applications that require deterministic
latency.

Table 1-23: Word Aligner Operations in Deterministic Latency State Machine Mode

Word Alignment Operation

PMA–PCS Interface

Width

PCS Mode

1. After the

rx_digitalreset

signal deasserts, a 0-to-1

transition in the

rx_enapatternalign

register

triggers the word aligner to look for the predefined word
alignment pattern, or its complement, in the received data
stream.

2. After the pattern is found and the word boundary is

identified, the state machine controls the deserializer to
clock-slip the boundary-indicated number of serial bits.

3. When clock-slip is complete, the deserialized data coming

into the receiver PCS is word-aligned and indicated when
the

rx_syncstatus

signal asserts.

10 bits

Single Width

20 bits

Double Width

Transceiver Architecture in Cyclone V Devices

Altera Corporation

Send Feedback

CV-53001

Word Aligner Operations in Deterministic Latency State Machine Mode

1-40

2013.05.06

«
...
325
326
327
328
329
...
»

Содержание Cyclone V






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Cyclone V

Бренд: Acconeer Страницы: 32

Бренд: Idis Страницы: 31

Anybus Communicator ABC4021

Бренд: HMS Networks Страницы: 60

AIE900-XNX Series

Бренд: AXIOMTEK Страницы: 53

Бренд: Paradyne Страницы: 10

Бренд: Seattle Computer Products Страницы: 31

D-NVR4108HS-4KS2/L

Бренд: Dahua Страницы: 33

Бренд: AMX Страницы: 1

Бренд: Technics Страницы: 20

NetVanta Analog Modem Dial Backup Interface Module

Бренд: ADTRAN Страницы: 2

Бренд: UNICORECOMM Страницы: 19

PROM Programming Adapters PCA7438F-64A

Бренд: Renesas Страницы: 18

Бренд: El.Mo Страницы: 16

Бренд: nox Страницы: 16

Бренд: RAK Страницы: 14

Бренд: TP-Link Страницы: 2

Бренд: Intel Страницы: 57

Бренд: Cambium Networks Страницы: 99

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды