Altera Cyclone V Скачать руководство пользователя страница 1030 | Manualshive

Страница: 1030 / 1077

Altera Cyclone V Скачать руководство пользователя страница 1030

HPStoFPGA and Lightweight HPS-to-FPGA Bridges

Table 28-2: HPStoFPGA and Lightweight HPS-to-FPGA Bridges and Clocks

Associated Clock Interface

(1)

Description

Interface Name

h2f_axi_clock

HPS-to-FPGA AXI master interface

h2f_axi_master

h2f_lw_axi_clock

HPS-to-FPGA lightweight AXI
master interface

h2f_lw_axi_master

The HPS-to-FPGA interface is a configurable data width AXI master (32, 64, or 128-bit) that allows HPS
masters to issue transactions to the FPGA fabric.

The lightweight HPS-to-FPGA interface is a 32-bit AXI master that allows HPS masters to issue transactions
to the FPGA fabric.

Both HPS-to-FPGA interfaces are AXI-3 compliant. The HPS-side AXI bridges manage clock crossing,
buffering, and data width conversion where necessary.

Other interface standards in the FPGA fabric, such as connecting to Avalon-MM interfaces, can be supported
through the use of soft logic adaptors. The Qsys system integration tool automatically generates adaptor
logic to connect AXI to Avalon-MM interfaces.

Each AXI bridge accepts a clock input from the FPGA fabric and performs clock domain crossing internally.
The exposed AXI interface operates on the same clock domain as the clock supplied by the FPGA fabric.

Related Information

•

on page 28-5

•

Features of the AXI Bridges

For more information, refer to the

HPS FPGA AXI Bridges Component

chapter.

FPGA-to-HPS SDRAM Interface

The FPGA-to-HPS SDRAM interface is a direct connection between the FPGA fabric and the HPS SDRAM
controller. This interface is highly configurable, allowing a mix between number of ports and port width.
The interface supports both AXI-3 and Avalon-MM protocols.

Altera Corporation

HPS Component Interfaces

Send Feedback

28-3

HPStoFPGA and Lightweight HPS-to-FPGA Bridges

cv_54028
2013.12.30

«
...
1028
1029
1030
1031
1032
...
»

Содержание Cyclone V






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов