Altera Cyclone V страница 755 Скачать руководство пользователя | Manualshive

Страница: 755 / 1077

background image

Figure 12-2: Data Slave Remapping Example

1 MB

Address Range

Data Slave

16-MB Flash Memory

Map to Offset 0

Map to Offset

0x00200000

0x01000000

0x00300000

0x00200000

0x00100000

0x00000000

Data

Slave

Access

Offsets

To remap the data slave to access other 1 MB regions of the flash device, enable address remapping in the
enable ARM

®

AMBA

®

advanced high speed bus (AHB) address remapping field (

enahbremap

) of the

cfg

register. All incoming data slave accesses remap to the offset specified in the remap address register

(

remapaddr

).

The 20 LSBs of incoming addresses are used for accessing the 1 MB region and the higher bits are ignored.

The quad SPI controller does not issue any error status for accesses that lie outside the connected
flash memory space.

Note:

Indirect Access Mode

In indirect access mode, flash data is temporarily buffered in the quad SPI controller’s static RAM (SRAM).
Software controls and triggers indirect accesses through the register slave interface. The controller transfers
data through the data slave interface.

Indirect Read Operation

An indirect read operation reads data from the flash memory, places the data into the SRAM, and transfers
the data to an external master through the data slave interface. The indirect read operations are controlled
by the following registers:

• Indirect read transfer register (

indrd

)

• Indirect read transfer watermark register (

indrdwater

)

• Indirect read transfer start address register (

indrdstaddr

)

• Indirect read transfer number bytes register (

indrdcnt

)

• Indirect address trigger register (

indaddrtrig

)

These registers need to be configured prior to issuing indirect read operations. The start address needs to
be defined in the

indrdstaddr

register and the total number of bytes to be fetched is specified in the

indircnt

register. Writing 1 to the start indirect read bit (

start

) of the

indrd

register triggers the

indirect read operation from the flash memory to populate the SRAM with the returned data.

To read data from the flash device into the SRAM, an external master issues 32-bit read transactions to the
data slave interface. The address of the read access must be in the indirect address range. You can configure
the indirect address through the

indaddrtrig

register. The external master can issue 32-bit reads until

Quad SPI Flash Controller

Altera Corporation

Send Feedback

cv_54012

Indirect Access Mode

12-4

2013.12.30

«
...
753
754
755
756
757
...
»

Содержание Cyclone V






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Cyclone V

Бренд: XDS Страницы: 99

Бренд: ebm-papst Страницы: 6

Бренд: ebm-papst Страницы: 6

Бренд: ebm-papst Страницы: 5

Бренд: Harmonic Страницы: 56

InterReach Fusion ADCP-77-044

Бренд: TE Connectivity Страницы: 236

Бренд: LogLogic Страницы: 30

Kinetic FLT 80 D5/DDC Body

Бренд: EK-Quantum Страницы: 16

Бренд: HARTING Страницы: 13

F-Tile SDI II Intel Agilex

Бренд: Intel Страницы: 39

Бренд: ICP DAS USA Страницы: 8

AyrMesh IndoorAP

Бренд: AYRSTONE Страницы: 2

Бренд: Idis Страницы: 16

Бренд: ZIMO Страницы: 13

Бренд: Kentrox Страницы: 246

Бренд: Agilent Technologies Страницы: 458

Бренд: SeaLevel Страницы: 19

Бренд: Baicells Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды