Yealink VC110 Administrator'S Manual Download Page 74

Page: 74 / 268

Administrator‘s Guide for Yealink VC110 Video Conferencing Endpoint

Parameter

Description

Configuration Method

parameter, the endpoint will
reboot to make the change take
effect.

Subnet Mask

Configures the subnet mask
assigned to the endpoint.

Default: Blank

Note: If you change this
parameter, the endpoint will
reboot to make the change take
effect.

Remote Control

Web User Interface

Gateway

Configures

the gateway

assigned to the endpoint.

Default: Blank

Note: If you change this
parameter, the endpoint will
reboot to make the change take
effect.

Remote Control

Web User Interface

Static DNS

Triggers the static DNS feature to
on or off.

Default: Off

Note: If you change this
parameter, the endpoint will
reboot to make the change take
effect.

Remote Control

Web User Interface

Primary DNS

Configures

the primary DNS

server assigned to the endpoint.

Default: Blank

Note: If you change this
parameter, the endpoint will
reboot to make the change take
effect.

Remote Control

Web User Interface

Secondary DNS

Configures

the secondary DNS

server assigned to the endpoint.

Default: Blank

Note: If you change this
parameter, the endpoint will
reboot to make the change take
effect.

Remote Control

Web User Interface

Summary of Contents for VC110













































































































































































































































































Search results

Summary of Contents for VC110

Reviews:

Related manuals for VC110

Brands by name

Popular brands

Yealink VC110, Administrator'S Manual

Search results

Summary of Contents for VC110

Reviews:

Related manuals for VC110

Brands by name

Popular brands