Yealink VC110 Administrator'S Manual Download Page 123

Page: 123 / 268

Configuring Call Preferences

111

This chapter provides information on how to configure endpoint‘s call preferences (e.g.,
call type and network bandwidth).

This chapter provides the following sections:



Configuring SIP Settings



Configuring H.323 Settings























Yealink VC110 video conferencing endpoint supports Session Initiation Protocol (SIP). If
your server supports SIP, you can use SIP to establish calls.

To establish calls using SIP, you can configure a SIP account for the endpoint.

SIP account parameters on the endpoint are described below:

Parameter

Description

Configuration Method

SIP Account

Enables or disables the SIP
account.

Default: Enabled

Remote Control

Web User Interface

Configures the user name of the
SIP account for register

Remote Control

Web User Interface

Summary of Contents for VC110













































































































































































































































































Search results

Summary of Contents for VC110

Reviews:

Related manuals for VC110

Brands by name

Popular brands

Yealink VC110, Administrator'S Manual

Search results

Summary of Contents for VC110

Reviews:

Related manuals for VC110

Brands by name

Popular brands