manualshive.com logo in svg

Yealink VC110, Administrator'S Manual

The Yealink VC110 is an advanced video conferencing system that offers seamless communication and collaboration. To get the most out of this powerful device, you can easily download the user manual for free from our website, ensuring a smooth user experience and optimal utilization of its features.

Share
Download
background image

Configuring Network

 

77 

5.

 

Click Confirm to accept the change. 

A dialog box pops up to prompt that the settings will take effect after a reboot. 

6.

 

Click OK to reboot the phone. 

To configure VLAN via the remote control: 

1.

 

Select Menu->Advanced (default password: 0000) ->Advanced Network. 

2.

 

In the VLAN block, check the Active checkbox. 

3.

 

Enter the VLAN ID in the VID(1-4094) field. 

4.

 

Enter the priority value (0-7) in the Priority field. 

5.

 

Press the Save soft key to accept the change. 

The display device prompts ―Reboot now?‖. 

6.

 

Select OK to reboot the endpoint immediately. 

The endpoint supports VLAN discovery via DHCP. When the VLAN Discovery method is 
set to DHCP, the endpoint will examine the DHCP option for a valid VLAN ID. The 
predefined option 132 is used to supply the VLAN ID by default. You can customize the 
DHCP option used to request the VLAN ID. 

Parameters of VLAN feature on the endpoint are described below. 

Parameter 

Description 

Configuration Method 

DHCP 

VLAN

->

Active 

Enables or disables the DHCP 
VLAN discovery feature on the 
endpoint. 

Default: Enabled 

Note: If you change this 
parameter, the endpoint will 
reboot to make the change take 
effect. 

Web User Interface 

Option 

Configures the DHCP option from 
which the endpoint obtains the 
VLAN settings. 

You can configure at most five 
DHCP options and separate them 
by commas. 

Valid Values: 128-254 

Default: 132 

Note: If you change this 
parameter, the endpoint will 

Web User Interface 

Summary of Contents for VC110













































































































































































































































































Reviews:

No comments

Related manuals for VC110

N-Com BX4 PLUS User Instructions And Safety preview
BX4 PLUS
Brand: N-Com Pages: 32
Intellitec iConnex User Manual preview
iConnex
Brand: Intellitec Pages: 16
Barco Cine VERSUM 50 Owner'S Manual preview
Cine VERSUM 50
Brand: Barco Pages: 37
Avaya IX Room Systems XT Series Release Notes preview
IX Room Systems XT Series
Brand: Avaya Pages: 41
Edis 020017-1 User Manual preview
020017-1
Brand: Edis Pages: 39
Roadstar CDR-485US/BK Instruction Manual preview
CDR-485US/BK
Brand: Roadstar Pages: 26
Qtx PPA72 User Manual preview
PPA72
Brand: Qtx Pages: 5
Lenze EtherNet/IP E84DGFCGEJP Communications Manual preview
EtherNet/IP E84DGFCGEJP
Brand: Lenze Pages: 149
Raven SCS 4600 Installation And Operation Manual preview
SCS 4600
Brand: Raven Pages: 104
Sharp XL-DAB701 Quick Start Manual preview
XL-DAB701
Brand: Sharp Pages: 2
Sharp XL-DAB151PH Operation Manual preview
XL-DAB151PH
Brand: Sharp Pages: 28
Philips OccuSwitch Wireless Installation Manual preview
OccuSwitch Wireless
Brand: Philips Pages: 2
Philips LDTS07 User Manual preview
LDTS07
Brand: Philips Pages: 10
Philips ILS-CL-6RES User Manual preview
ILS-CL-6RES
Brand: Philips Pages: 22
Philips SBC SK 310 Instructions For Use Manual preview
SBC SK 310
Brand: Philips Pages: 26
Philips LIGHTOLIER CONTROLS LYTESCENE ILSCLTSII User Manual preview
LIGHTOLIER CONTROLS LYTESCENE ILSCLTSII
Brand: Philips Pages: 36
Philips SpaceWice User Manual preview
SpaceWice
Brand: Philips Pages: 42
Aastra 5380 User Manual preview
5380
Brand: Aastra Pages: 166

Brands by name

Popular brands

Load more brands