Yealink VC110 Administrator'S Manual Download Page 5 | Manualshive

Page: 5 / 268

background image

About This Guide

v

Thank you for choosing the Yealink VC110 full HD video conferencing endpoint. It is an
all-in-one unit that supports 1080P-full HD video conferencing and includes outstanding
features such as good compatibility, easy deployment and intelligent network
adaptability. These make it the best choice for SME.

The Yealink VC110 full-HD video conferencing endpoint is designed to help enterprises
organize video conferences easily and efficiently. Users can expect to enjoy the
high-quality video conferencing experience very cost-effectively.

The guide is intended for administrators who need to configure, customize, manage,
and troubleshoot the video conferencing endpoint properly, rather than for end-users. It
provides details on the functionality and configuration of the Yealink VC110 endpoint.

Many of the features described in this guide involve network and account settings,
which could affect the endpoint‘s performance in the network. Therefore, an
understanding of IP networking and a prior knowledge of VoIP telephony concepts are
necessary.

This guide covers the VC110 video conferencing endpoint. In addition to the
administrator guide, the following related documents are available:



Quick Start Guide, which describes how to assemble the endpoint and configure
basic network features on the endpoint.



User Guide, which describes how to configure and use basic features available on
the endpoints.



Video Conference Room Deployment Solution, which describes the conference
room layout requirements and how to deploy the endpoints.



Network Deployment Solution, which describes how to deploy network for your
systems.

You can download the above documentations online:

http://support.yealink.com/documentFront/forwardToDocumentFrontDisplayPage

For support or service, please contact your Yealink reseller or go to Yealink Technical
Support online:

http://www.yealink.com/Support.aspx

Common reasons for updating firmware include fixing bugs or adding features to the

«
...
3
4
5
6
7
...
»

Summary of Contents for VC110













































































































































































































































































Reviews:

No comments

Related manuals for VC110

Brand: Dahua Pages: 58

Brand: DayTronic Pages: 414

COMPETITION ProZ4-80

Brand: µ-Dimension Pages: 7

Brand: Absima Pages: 5

Brand: Tokai Pages: 20

Brand: elsner elektronik Pages: 148

Brand: JAMO Pages: 72

Brand: Vizio Pages: 24

Brand: ENTRYPASS Pages: 27

ConferenceSHOT AV

Brand: VADDIO Pages: 34

Videoconferencing system

Brand: PictureTel Pages: 122

Brand: THOMSON Pages: 63

Brand: Kramer Pages: 4

Brand: HME Pages: 2

Brand: Magnetic Autocontrol Pages: 132

Brand: Powerdist Pages: 7

Brand: Blaupunkt Pages: 13

Brand: Aventura Pages: 55

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands