Yealink VC110 Administrator'S Manual Download Page 53 | Manualshive

Page: 53 / 268

background image

Getting Started

41

This chapter provides basic information and installation instructions for Yealink VC110
endpoints in the following sections:



Endpoint Connection and Installation



Powering the Endpoint On or Off



Endpoint Initialization



Endpoint Startup





Enabling Communication with Other Endpoints



Placing a Test Call from the Yealink VC110 endpoint

Placing the Endpoint

Do not place the camera facing a window or other bright light. Ensure sufficient space to
connect the cables. Ensure all participants are facing both the display device and the
camera at the same time by putting camera and display device together.

Endpoint Components Installation

This section introduces the following:



Connecting the VC110 video conferencing endpoint



Installing the VC110 video conferencing endpoint



Installing batteries in the remote control

Note

Up to two display devices can be connected to

the

VC110 all-in-one unit. Because the

display device is not included in the package, you need to purchase it separately if
required. Ensure that the purchased display device supports HDMI input.

When connecting only one display device to the VC110 all-in-one unit, Display1 port is
the only available port. If dual screen mode is required, you can connect s

econdary

display device to the Display2 port.

Because DVI cable is tailor-made, please use the Yealink-supplied DVI cable.

To prevent shock, do not connect the power adapter and turn on the power before
connecting all endpoint components.

«
...
51
52
53
54
55
...
»

Summary of Contents for VC110













































































































































































































































































Reviews:

No comments

Related manuals for VC110

Brand: iHome Pages: 17

Brand: Xantech Pages: 102

Brand: Panasonic Pages: 1

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 20

Brand: GSK Pages: 32

Brand: HK Audio Pages: 20

ADAP-KOOL AK-SM 800

Brand: Danfoss Pages: 4

Brand: Roadstar Pages: 80

Brand: Goodmans Pages: 15

Brand: Steg Pages: 8

Brand: SKF Pages: 63

Brand: Regintech Pages: 82

Brand: On-Hold Plus Pages: 12

Brand: Paso Pages: 8

SENTEX Infinity B Series

Brand: Chamberlain Pages: 35

Brand: Cambium Networks Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands