manualshive.com logo in svg

Yealink VC110, Administrator'S Manual

The Yealink VC110 is an advanced video conferencing system that offers seamless communication and collaboration. To get the most out of this powerful device, you can easily download the user manual for free from our website, ensuring a smooth user experience and optimal utilization of its features.

Share
Download
background image

Administrator‘s Guide for Yealink VC110 Video Conferencing Endpoint 

166 

The MTU parameter on the endpoint is described below.   

Parameter 

Description 

Configuration Method 

Video MTU 

Specifies the maximum MTU size 
(in bytes) of video packets sent 
by the endpoint. 

Valid Values: Integer from 1000 to 
1500 

Default: 1500 

Note: If you change this 
parameter, the endpoint will 
reboot to make the change take 
effect. 

Remote Control 

Web User Interface 

To configure MTU via web user interface: 

1.

 

Click on Network->Advanced. 

2.

 

In the MTU block, enter the desired value in the Video MTU field. 

 

3.

 

Click Confirm to accept the change. 

A dialog box pops up to prompt that the settings will take effect after a reboot. 

4.

 

Click Confirm to reboot the endpoint immediately. 

To configure MTU via the remote control: 

1.

 

Select Menu->Advanced (default password: 0000) ->Advanced Network. 

Summary of Contents for VC110













































































































































































































































































Reviews:

No comments

Related manuals for VC110

Fagor CNC 8070 Original Instructions Manual preview
CNC 8070
Brand: Fagor Pages: 10
Fagor CNC 8060 Operating Manual preview
CNC 8060
Brand: Fagor Pages: 172
Fagor CNC 8060 Hardware Configuration preview
CNC 8060
Brand: Fagor Pages: 112
Jensen JMS32 Owner'S Manual preview
JMS32
Brand: Jensen Pages: 41
ClearOne Collaborate FHD User Manual preview
Collaborate FHD
Brand: ClearOne Pages: 82
Evil Mad Scientist Ostrich Eggbot 2.0 Assembly Manual preview
Ostrich Eggbot 2.0
Brand: Evil Mad Scientist Pages: 45
Micronix MMC-100 Series Quick Start Manual preview
MMC-100 Series
Brand: Micronix Pages: 16
Fusion FUS-SW104 User Manual preview
FUS-SW104
Brand: Fusion Pages: 4
InnoMedia InfoView IV 2000 Operating Manual preview
InfoView IV 2000
Brand: InnoMedia Pages: 50
lee handels Happy Call Series Manual And Security Instructions preview
Happy Call Series
Brand: lee handels Pages: 13
Eaton Greengate ControlKeeper 4 Installation Instructions Manual preview
Greengate ControlKeeper 4
Brand: Eaton Pages: 24
T+A DD 820 M User Manual preview
DD 820 M
Brand: T+A Pages: 70
Avaya Tandberg 150 MXP Installation Instructions Manual preview
Tandberg 150 MXP
Brand: Avaya Pages: 13
Adcom GFI-4400 Owner'S Manual preview
GFI-4400
Brand: Adcom Pages: 16
RCA RS2046 User Manual preview
RS2046
Brand: RCA Pages: 1
Foxtech T30 User Manual preview
T30
Brand: Foxtech Pages: 63
Nibe MODBUS 40 Installer Manual preview
MODBUS 40
Brand: Nibe Pages: 32
AMX VTX-1S Product Dimensions preview
VTX-1S
Brand: AMX Pages: 1

Brands by name

Popular brands

Load more brands