Yealink VC110 Administrator'S Manual Download Page 156 | Manualshive

Page: 156 / 268

background image

Administrator‘s Guide for Yealink VC110 Video Conferencing Endpoint

144

Parameter

Description

Configuration Method

Default: Yealink VC110

To configure the site name via web user interface:

1.

Click on Setting->General.

2.

Edit the site name in the Site Name field.

3.

Click Confirm to accept the change.

The LCD screen of the display device and video conferencing phone will display
the changed site name.

To configure the site name via the remote control:

1.

Select Menu->Basic.

2.

Edit the site name in the Site Name field.

3.

Press the Save soft key to accept the change.

The LCD screen of the display device and video conferencing phone will display
the changed site name.

Backlight determines the brightness of the LCD screen display, allowing users to read
easily in dark environments. Backlight time specifies the delay time to turn off the
backlight when the phone is inactive.

You can configure the backlight time as one of the following types:



Always On: Backlight is turned on permanently.



15 s, 30 s, 10 min, 20 min, 30 min, 1 Hour, 2 Hour, 3 Hour, 4 Hour:

Backlight is turned

off when the phone is inactive after a preset period of time. It is automatically
turned on if the status of the phone changes or any key is pressed.

«
...
154
155
156
157
158
...
»

Summary of Contents for VC110













































































































































































































































































Reviews:

No comments

Related manuals for VC110

ProducTVity Station

Brand: red lion Pages: 8

Brand: Thermo Scientific Pages: 68

Magnavox FW 55C

Brand: Magnavox Pages: 80

Brand: YARMEE Pages: 7

Studio 500 Series

Brand: JAMO Pages: 16

Brand: Retekess Pages: 9

Brand: Bame Pages: 12

Brand: Daewoo Pages: 35

Brand: Nakamichi Pages: 14

Brand: B&R Industries Pages: 16

Brand: Mantracourt Pages: 24

Brand: Emerson Pages: 16

Brand: Emerson Pages: 2

Brand: Emerson Pages: 8

Brand: Emerson Pages: 28

Brand: Emerson Pages: 36

Brand: Emerson Pages: 14

Brand: Emerson Pages: 31

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands