manualshive.com logo in svg

Yealink VC110, Administrator'S Manual

The Yealink VC110 is an advanced video conferencing system that offers seamless communication and collaboration. To get the most out of this powerful device, you can easily download the user manual for free from our website, ensuring a smooth user experience and optimal utilization of its features.

Share
Download
background image

Configuring Network

 

97 

3.

 

Click Confirm to accept the change. 

To configure STUN for SIP IP call via web user interface: 

1.

 

Click on Account->SIP IP Call. 

2.

 

Select STUN from the pull-down list of NAT_Traversal. 

 

3.

 

Click Confirm to accept the change. 

To configure STUN server via the remote control: 

1.

 

Select Menu->Advanced (default password: 0000) ->NAT/Firewall. 

Mark the ON radio box in the STUN Active field. 

2.

 

Enter the IP address or the domain name of the STUN server in the STUN Server 
field. 

3.

 

Enter the port of the STUN server in the Port field. 

4.

 

Press the Save soft key to accept the change. 

To configure STUN server for SIP IP call via the remote control: 

1.

 

Select Menu->Advanced (default password: 0000) ->SIP IP Call. 

2.

 

Select STUN from the pull-down list of NAT_Traversal. 

3.

 

Press the Save soft key to accept the change. 

Full Cone:   

A full cone NAT is one where all requests from the same internal IP address and port are 
mapped to the same external IP address and port. Furthermore, any external host can 
send a packet to the internal host, by sending a packet to the mapped external 
address. 

Summary of Contents for VC110













































































































































































































































































Reviews:

No comments

Related manuals for VC110

Kramer KIT-Z100 Quick Start Manual preview
KIT-Z100
Brand: Kramer Pages: 4
Burmester 151 Musiccenter Short Operating Instructions preview
151 Musiccenter
Brand: Burmester Pages: 20
Poly P020 User Manual preview
P020
Brand: Poly Pages: 28
Pyle PLMR7BTW Owner'S Manual preview
PLMR7BTW
Brand: Pyle Pages: 12
Xilinx Zynq UltraScale+ User Manual preview
Zynq UltraScale+
Brand: Xilinx Pages: 86
Multilaser Royal P3159 User Manual preview
Royal P3159
Brand: Multilaser Pages: 25
Hitachi YUTAKI ATW-YMM-01 Installation And Operation Manual preview
YUTAKI ATW-YMM-01
Brand: Hitachi Pages: 128
Hitachi Relion 670 Series Product Manual preview
Relion 670 Series
Brand: Hitachi Pages: 192
Sharp CD-XP160W Operation Manual preview
CD-XP160W
Brand: Sharp Pages: 32
Philips FW-C90 Specifications preview
FW-C90
Brand: Philips Pages: 2
Philips FW-C870 Specifications preview
FW-C870
Brand: Philips Pages: 2
Philips FW-C85/18 Specifications preview
FW-C85/18
Brand: Philips Pages: 2
Philips FW-C80 Specifications preview
FW-C80
Brand: Philips Pages: 2
Philips FW-C90 User Manual preview
FW-C90
Brand: Philips Pages: 29
Philips FW-C870 User Manual preview
FW-C870
Brand: Philips Pages: 30
Philips FW-D596 User Manual preview
FW-D596
Brand: Philips Pages: 48
Philips FW-D5/21 Service Manual preview
FW-D5/21
Brand: Philips Pages: 100
Philips FW-C870/19 Service Manual preview
FW-C870/19
Brand: Philips Pages: 105

Brands by name

Popular brands

Load more brands