Yealink VC110 Administrator'S Manual Download Page 204 | Manualshive

Page: 204 / 268

background image

Administrator‘s Guide for Yealink VC110 Video Conferencing Endpoint

192

It will prevent importing the title of the contact information which is located in the
first line of the CSV file.

6.

(Optional.) Check the Delete Old Contacts checkbox.

It will delete all existing contacts while importing the contact list.

7.

Select the desired value from the pull-down list.

-

If Ignore is selected, this column will not be imported to the endpoint.

-

If Display Name is selected, this column will be imported to the endpoint as the
contacts‘ name.

-

If number1/2/3 is selected, this column will be imported to the endpoint as the
contacts‘ number.

8.

Click Confirm to complete importing the contact list.

The web user interface prompts "Contacts imported successfully!".

To export a XML/CSV file of the contact list via web user interface:

1.

Click on Directory->Local Directory.

2.

Click Import/Export, and select Export XML or Export CSV.

3.

The contact list is saved to your local endpoint.

LDAP (Lightweight Directory Access Protocol) is an application protocol for accessing
and maintaining information services for the distributed directory over an IP network.
Yealink VC110 endpoint

is configurable to interface with a corporate directory server

that supports LDAP version 2 or 3. The following LDAP servers are supported:

«
...
202
203
204
205
206
...
»

Summary of Contents for VC110













































































































































































































































































Reviews:

No comments

Related manuals for VC110

ElectraElite IPK

Brand: NEC Pages: 20

Brand: SereneLife Pages: 2

Brand: Daewoo Pages: 35

Brand: Nakamichi Pages: 14

Brand: Alpine Pages: 16

Brand: X4-TECH Pages: 2

Brand: McIntosh Pages: 32

Brand: Panasonic Pages: 68

Brand: Panasonic Pages: 18

Brand: 3M Pages: 90

Brand: JVC Pages: 36

Brand: JVC Pages: 74

Brand: Kenwood Pages: 27

Brand: Kenwood Pages: 12

Brand: Kenwood Pages: 2

Brand: Kenwood Pages: 24

Brand: Kenwood Pages: 59

Brand: Kenwood Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands