Yealink VC110 Administrator'S Manual Download Page 182 | Manualshive

Page: 182 / 268

background image

Administrator‘s Guide for Yealink VC110 Video Conferencing Endpoint

170

Content sharing allows users to share content with other conference participants during
a call. When a PC is connected to the PC port on the VC110 all-in-one unit, the display
device can display both the camera video and the shared content. The content sharing
feature is very useful in the conference scenario in which content sharing is needed
(e.g., a slide or a flash).

During a conference call, the far site may not support receiving shared content. In this
case, you can enable mix sending feature on the endpoint. Mix sending feature allows
the sender to compound multiple video streams (local image+shared content) to one
video stream, and then send it to the far site.

The mix sending parameter on the endpoint is described below.

Parameter

Description

Configuration Method

Mix

Enables or disables the mix
sending feature on the endpoint.

Default: Enabled

Web User Interface

To configure mix sending via web user interface:

1.

Click on Setting->Video & Audio.

2.

In the Presentation block, select the desired value from the pull-down list of Mix.

3.

Click Confirm to accept the change.

«
...
180
181
182
183
184
...
»

Summary of Contents for VC110













































































































































































































































































Reviews:

No comments

Related manuals for VC110

Brand: Samsung Pages: 42

Brand: Eagle Copters Pages: 11

Brand: Panasonic Pages: 4

Brand: Caliber Pages: 12

Brand: Grandstream Networks Pages: 27

Brand: Vizio Pages: 24

Brand: Polycom Pages: 10

Brand: Jensen Marine Pages: 18

Brand: Sennheiser Pages: 1

Brand: PASCO Pages: 2

Brand: DIS Pages: 2

Brand: Tokai Pages: 42

Brand: Wavemaster Pages: 32

Lumina LU20S-DNW

Brand: Leviton Pages: 3

Brand: Huawei Pages: 109

Brand: Huawei Pages: 37

Brand: Huawei Pages: 8

Brand: Huawei Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands