Yealink VC110 Administrator'S Manual Download Page 130

Page: 130 / 268

Administrator‘s Guide for Yealink VC110 Video Conferencing Endpoint

118

Parameter

Description

Configuration Method

tunneling on the endpoint.

Default: Disabled

For more information, refer to

H.323 Tunneling

on page

Web User Interface

H235 Encryption

Specifies the H.235 type for the
H.323 account.



Disabled—do not use
H.235 in H.235 calls.



Optional—negotiate with
the far site whether to use
H.235 for media encryption
in H.323 calls.



Compulsory—compulsory
use H.235 for media
encryption in H.323 calls.

Default: Disabled

For more information, refer to

H.235

on page

218

Web User Interface

Protocol Monitor

Port

Specifies the port for the H.323
protocol.

Default 1720.

Note: It is only applicable to IP
call.

Web User Interface

Local Early Media

Enables or disables local early
media feature on the endpoint.

Default: Disabled.

If it is set to Enabled, the
endpoint will send video SDP
twice during a call to solve the
compatibility between Yealink
device and certain devices.

Web User Interface

To configure H.323 account via web user interface:

Click on Account->H323.

Summary of Contents for VC110













































































































































































































































































Search results

Summary of Contents for VC110

Reviews:

Related manuals for VC110

Brands by name

Popular brands

Yealink VC110, Administrator'S Manual

Search results

Summary of Contents for VC110

Reviews:

Related manuals for VC110

Brands by name

Popular brands