manualshive.com logo in svg

Yealink VC110, Administrator'S Manual

The Yealink VC110 is an advanced video conferencing system that offers seamless communication and collaboration. To get the most out of this powerful device, you can easily download the user manual for free from our website, ensuring a smooth user experience and optimal utilization of its features.

Share
Download
background image

Configuring Network

 

83 

4)    Click Upload to upload the certificate. 

 

3.

 

Click Confirm to accept the change. 

A dialog box pops up to prompt that the settings will take effect after a reboot. 

4.

 

Click Confirm to reboot the endpoint immediately. 

To configure the 802.1X via the remote control: 

1.

 

Select Menu->Advanced (default password: 0000) ->Advanced Network. 

2.

 

Select the desired mode from the pull-down list of 802.1x Mode. 

3.

 

Press the Save soft key to accept the change. 

The display device prompts ―Reboot now?‖. 

4.

 

Select OK to reboot the endpoint immediately. 

The H.245 protocol is a control protocol that manages the media sessions. It is a part of 
the H.323 protocol suite. The H.245 protocol is used primarily to negotiate the 
master-slave relationship between communicating endpoints. The H.245 messages can 
be encapsulated and carried between H.225 controlled endpoints within H.225 
messages. This way of "piggy-backing" an H.245 message to the H.225 message is 
referred to as H.323 Tunneling. The tunneling feature relies on H.225 
endpoint-to-endpoint connectivity (via TCP) to pass H.245 messages, and uses the 
H.225 communication channel without creating a separate TCP socket connection (per 
H.323 call) for media control. 

Summary of Contents for VC110













































































































































































































































































Reviews:

No comments

Related manuals for VC110

3M XT-1 Technical Data preview
XT-1
Brand: 3M Pages: 2
3M XT-1 Technical Bulletin preview
XT-1
Brand: 3M Pages: 2
S&S Northern Merlin 1000VW+ Installation, Operating And Maintenance preview
Merlin 1000VW+
Brand: S&S Northern Pages: 9
Magnavox FW 560C Owner'S Manual preview
FW 560C
Brand: Magnavox Pages: 78
AETA Scoopy+ S User Manual preview
Scoopy+ S
Brand: AETA Pages: 136
Fagerhult e-Sense Actilume Manual preview
e-Sense Actilume
Brand: Fagerhult Pages: 9
dB Technologies RW 16MS/BS Quick Start User Manual preview
RW 16MS/BS
Brand: dB Technologies Pages: 2
Okuma VTM-200 Operation & Maintenance Manual preview
VTM-200
Brand: Okuma Pages: 109
Cisco MCS 7800 Series Administrator'S Manual preview
MCS 7800 Series
Brand: Cisco Pages: 234
Cisco TelePresence Administrator'S Manual preview
TelePresence
Brand: Cisco Pages: 507
Cisco TelePresence Specifications preview
TelePresence
Brand: Cisco Pages: 7
Cisco ICS-7750 Description preview
ICS-7750
Brand: Cisco Pages: 174
Cisco Webex Room Kit Pro Installation Manual preview
Webex Room Kit Pro
Brand: Cisco Pages: 21
Cisco TelePresence Installation Manual preview
TelePresence
Brand: Cisco Pages: 4
Cisco Webex Room Panorama Installation Manual preview
Webex Room Panorama
Brand: Cisco Pages: 88
Cisco Webex Room Kit Plus Precision 60 Installation Manual preview
Webex Room Kit Plus Precision 60
Brand: Cisco Pages: 16
Cisco Webex Room Kit Mini Installation Manual preview
Webex Room Kit Mini
Brand: Cisco Pages: 32
Cisco DX650 Administration Manual preview
DX650
Brand: Cisco Pages: 230

Brands by name

Popular brands

Load more brands