manualshive.com logo in svg

Yealink VC110, Administrator'S Manual

The Yealink VC110 is an advanced video conferencing system that offers seamless communication and collaboration. To get the most out of this powerful device, you can easily download the user manual for free from our website, ensuring a smooth user experience and optimal utilization of its features.

Share
Download
background image

Administrator‘s Guide for Yealink VC110 Video Conferencing Endpoint 

92 

Parameter 

Description 

Configuration Method 

Default: Disabled 

Note: Static NAT works only if this 
parameter is set to StaticNat. 

To configure static NAT via web user interface: 

1.

 

Click on Network->NAT/Firewall. 

2.

 

Select the desired value from the pull-down list of Static NAT. 

3.

 

Configure the NAT public address in the NAT Public IP Address field if Manual is 
selected from the pull-down list of Static NAT. 

4.

 

If multi-level intranet network has deployed in your environment, and you 
experience the one-way audio or video problem, select Compulsory from the 
pull-down list of Route Traversal to solve this problem. 

 

5.

 

Click Confirm to accept the change. 

To configure Static NAT for SIP account via web user interface: 

1.

 

Click on Account->SIP Account. 

 

 

Summary of Contents for VC110













































































































































































































































































Reviews:

No comments

Related manuals for VC110

Daktronics RC-100 Operation Manual preview
RC-100
Brand: Daktronics Pages: 52
iDance XD25 Instruction Manual preview
XD25
Brand: iDance Pages: 10
Yamaha PJP-EC200 Setup Procedure preview
PJP-EC200
Brand: Yamaha Pages: 14
Yamaha PJP-50R Basic Operation Manual preview
PJP-50R
Brand: Yamaha Pages: 28
Yamaha CS-700 Series Operation Manual preview
CS-700 Series
Brand: Yamaha Pages: 109
Yamaha PJP-100UH Additional Information preview
PJP-100UH
Brand: Yamaha Pages: 3
Yamaha CBX-D5 Troubleshooting Manual preview
CBX-D5
Brand: Yamaha Pages: 4
Measurement Computing CIO-DAS1401/12 User Manual preview
CIO-DAS1401/12
Brand: Measurement Computing Pages: 32
D&R ELECTRONICS RDS17S-ELITE1-R1 Installation Manual preview
RDS17S-ELITE1-R1
Brand: D&R ELECTRONICS Pages: 12
ION iAS01 Quick Start Manual preview
iAS01
Brand: ION Pages: 48
Teac CR-K1 Service Manual preview
CR-K1
Brand: Teac Pages: 16
A-T Controls TRIAO TMC-4 Installation And Operation Manual preview
TRIAO TMC-4
Brand: A-T Controls Pages: 19
Shure IS 6132 User Manual preview
IS 6132
Brand: Shure Pages: 18
Intermatic PJB2175 Installation, Operation & Service Manual preview
PJB2175
Brand: Intermatic Pages: 2
DIS DDS 5900 User Manual preview
DDS 5900
Brand: DIS Pages: 54
Balboa Instruments Poolux Installation And Configuration Manual preview
Poolux
Brand: Balboa Instruments Pages: 76
Champion CHVS310 User Manual preview
CHVS310
Brand: Champion Pages: 46
babala Hydro-Pro Instruction Manual preview
Hydro-Pro
Brand: babala Pages: 30

Brands by name

Popular brands

Load more brands