Yealink VC110 Administrator'S Manual Download | Manualshive

Page: 71 / 268

background image

Configuring Network

59

To configure DHCP via the remote control:

1.

Select Menu->Advanced (default password: 0000) ->LAN Configuration->IPv4.

2.

Check the DHCP checkbox.

3.

Press the Save soft key to accept the change.

The display device prompts ―Reboot now?‖.

4.

Select OK to reboot the endpoint immediately.

Even though DHCP is enabled, you can manually configure the static DNS address(es).

Parameters of static DNS on the endpoint are described below:

Parameter

Description

Configuration Method

Static DNS

Triggers the static DNS feature to
on or off.

Default: Off

Note: If it is set to Off, the
endpoint will use the IPv4 DNS
obtained from DHCP.

If it is set to On, the endpoint will
use manually configured static
IPv4 DNS.

It only works if the value of the
―IPv4 Config‖ is set to DHCP. If
you change this parameter, the
endpoint will reboot to make the
change take effect.

Remote Control

Web User Interface

Primary DNS

Configures the primary IPv4 DNS
server.

Default: Blank

Note: It only works if the value of
the "Static IPv4 DNS" is set to On.
If you change this parameter, the
endpoint will reboot to make the
change take effect.

Remote Control

Web User Interface

Secondary DNS

Configures the secondary IPv4
DNS server.

Default: Blank

Note: It only works if the value of

Remote Control

Web User Interface

«
...
69
70
71
72
73
...
»

Summary of Contents for VC110













































































































































































































































































Reviews:

No comments

Related manuals for VC110

Brand: Data I/O Pages: 88

Brand: JBL Pages: 16

Authentics L 16

Brand: JBL Pages: 17

Brand: Zeck Audio Pages: 16

Brand: Akura Pages: 11

AQUIS ULTRAFLOW

Brand: Waterous Pages: 217

Brand: TANDBERG Pages: 12

Brand: Barco Pages: 37

IX Room Systems XT Series

Brand: Avaya Pages: 41

Brand: Avaya Pages: 5

Brand: Magnetic Autocontrol Pages: 132

Brand: Favero Pages: 27

Brand: AudioBahn Pages: 15

Brand: Aastra Pages: 166

Brand: Sharp Pages: 2

Brand: Pioneer Pages: 13

Brand: Pioneer Pages: 10

Brand: Pioneer Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands