manualshive.com logo in svg

Yealink VC110, Administrator'S Manual

The Yealink VC110 is an advanced video conferencing system that offers seamless communication and collaboration. To get the most out of this powerful device, you can easily download the user manual for free from our website, ensuring a smooth user experience and optimal utilization of its features.

Share
Download
background image

Administrator‘s Guide for Yealink VC110 Video Conferencing Endpoint 

16 

To remove the VCM60 from the VC110 video conferencing endpoint, do the following: 

1.

 

Remove the dongle from the VC110 all-in-one unit. 

The display device prompts ―Dongle remove!‖. And the icon            disappears from 
the status bar. 

 

The VCM60 supports two standby modes: online standby and offline standby. 

Online standby:   

 

When registering with dongle successfully, the VCM60 enters online standby mode 
and the mute indicator LED changes to green and is in breathing state.   

Offline standby:   

 

If VC110 video conferencing endpoint encounters poor signal, wireless interference 
or is powered off, the VCM60 may lose connection with the dongle. In this case, the 
VCM60 will search the dongle again, and the mute indicator LED fast flashes green. 
If dongle cannot be searched in 2 minutes, the VCM60 will enter offline standby 
mode automatically and the mute indicator LED slowly flashes orange. 

 

When the VCM60 is in offline standby mode, you need to tap the mute button to 
activate VCM60 to search dongle again and the mute indicator LED fast flashes 
green. 

 

 

Summary of Contents for VC110













































































































































































































































































Reviews:

No comments

Related manuals for VC110

Panasonic KX-NS300 Cabling Configuration preview
KX-NS300
Brand: Panasonic Pages: 5
Panasonic KX-HTS Series Setup Reference Manual preview
KX-HTS Series
Brand: Panasonic Pages: 14
Panasonic HDVC-MPCS Specification preview
HDVC-MPCS
Brand: Panasonic Pages: 2
Panasonic VoiceSonic KX-NT700 Quick Reference Manual preview
VoiceSonic KX-NT700
Brand: Panasonic Pages: 8
Panasonic SC-HC57 Owner'S Manual preview
SC-HC57
Brand: Panasonic Pages: 24
Panasonic SC-AP01 Operating Instructions Manual preview
SC-AP01
Brand: Panasonic Pages: 16
Yealink CP935W Quick Start Manual preview
CP935W
Brand: Yealink Pages: 8
RKC INSTRUMENT FAREX SR MINI SYSTEM Communication Instruction Manual preview
FAREX SR MINI SYSTEM
Brand: RKC INSTRUMENT Pages: 82
Grandstream Networks GAC2570 User Manual preview
GAC2570
Brand: Grandstream Networks Pages: 177
Nakamichi NA99 Instruction Manual preview
NA99
Brand: Nakamichi Pages: 12
PictureTel Videoconferencing system User Manual preview
Videoconferencing system
Brand: PictureTel Pages: 122
RADVision SCOPIA XT MCU series Administrator'S Manual preview
SCOPIA XT MCU series
Brand: RADVision Pages: 43
VAT Series 651 Installation, Operating, & Maintenance Instructions preview
Series 651
Brand: VAT Pages: 53
ITC TS-0690 User Manual preview
TS-0690
Brand: ITC Pages: 15
Stahl ET-306-A Series Operating Instructions Manual preview
ET-306-A Series
Brand: Stahl Pages: 60
ELBE CDM-250-USB User Manual preview
CDM-250-USB
Brand: ELBE Pages: 19
iDance GROOVE 870 Operating Instructions Manual preview
GROOVE 870
Brand: iDance Pages: 16
Dormakaba SVP-S 4 DCW Series Mounting Instructions preview
SVP-S 4 DCW Series
Brand: Dormakaba Pages: 5

Brands by name

Popular brands

Load more brands