manualshive.com logo in svg

Yealink VC110, Administrator'S Manual

The Yealink VC110 is an advanced video conferencing system that offers seamless communication and collaboration. To get the most out of this powerful device, you can easily download the user manual for free from our website, ensuring a smooth user experience and optimal utilization of its features.

Share
Download
background image

Administrator‘s Guide for Yealink VC110 Video Conferencing Endpoint 

120 

DTMF Keypad Frequencies: 

 

1209 Hz 

1336 Hz 

1447 Hz 

1633 Hz 

697 Hz 

1 

2 

3 

A 

770 Hz 

4 

5 

6 

B 

852 Hz 

7 

8 

9 

C 

941 Hz 

* 

0 

# 

D 

Three methods of transmitting DTMF digits on SIP calls: 

 

RFC 2833 -- DTMF digits are transmitted by RTP Events compliant to RFC 2833. 

 

INBAND -- DTMF digits are transmitted in the voice band. 

 

SIP INFO -- DTMF digits are transmitted by SIP INFO messages. 

The method of transmitting DTMF digits is configurable on a per-line basis. 

RFC 2833 

DTMF digits are transmitted using the RTP Event packets that are sent along with the 
voice path. These packets use RFC 2833 format and must have a payload type that 
matches what the other end is listening for. The payload type for RTP Event packets is 
configurable. IP phones default to 101 for the payload type, which use the definition to 
negotiate with the other end during call establishment. 

The RTP Event packet contains 4 bytes. The 4 bytes are distributed over several fields 
denoted as Event, End bit, R-bit, Volume and Duration. If the End bit is set to 1, the 
packet contains the end of the DTMF event. You can configure the sending times of the 
end RTP Event packet. 

INBAND 

DTMF digits are transmitted within the audio of the IP phone conversation. It uses the 
same codec as your voice and is audible to conversation partners. 

SIP INFO 

DTMF digits are transmitted by the SIP INFO messages when the voice stream is 
established after a successful SIP 200 OK-ACK message sequence. The SIP INFO 
message is sent along the signaling path of the call. The SIP INFO message can transmit 
DTMF digits in three ways: DTMF, DTMF-Relay and Telephone-Event. 

 

 

Summary of Contents for VC110













































































































































































































































































Reviews:

No comments

Related manuals for VC110

Fagor 101 Operating Manual preview
101
Brand: Fagor Pages: 103
Fagor CNC 8070 Original Instructions Manual preview
CNC 8070
Brand: Fagor Pages: 10
Fagor CNC 8060 Operating Manual preview
CNC 8060
Brand: Fagor Pages: 172
Fagor CNC 8060 Hardware Configuration preview
CNC 8060
Brand: Fagor Pages: 112
D&R ELECTRONICS F5S-IQ Series Installation Manual preview
F5S-IQ Series
Brand: D&R ELECTRONICS Pages: 12
Polycom IPOWER 9000 Quick Tips preview
IPOWER 9000
Brand: Polycom Pages: 2
Magnetic Autocontrol MAGSTOP MIB 10-C090 Operating Instructions Manual preview
MAGSTOP MIB 10-C090
Brand: Magnetic Autocontrol Pages: 15
Panasonic SAPM38 - CD STEREO SYSTEM Operating Instructions Manual preview
SAPM38 - CD STEREO SYSTEM
Brand: Panasonic Pages: 48
Panasonic SA-MAX4000E Service Manual preview
SA-MAX4000E
Brand: Panasonic Pages: 31
Panasonic SA-MAX5000GM Service Manual preview
SA-MAX5000GM
Brand: Panasonic Pages: 40
Panasonic SA-EN37 Operating Instructions Manual preview
SA-EN37
Brand: Panasonic Pages: 8
Panasonic SA-EN35DB Operating Instructions Manual preview
SA-EN35DB
Brand: Panasonic Pages: 12
Panasonic SA-MAX670P Series Service Manual preview
SA-MAX670P Series
Brand: Panasonic Pages: 64
Panasonic SA-EN29 Operating Instructions Manual preview
SA-EN29
Brand: Panasonic Pages: 12
Panasonic SA-HC7 Operating Instructions Manual preview
SA-HC7
Brand: Panasonic Pages: 32
Panasonic SA-EN28P Service Manual preview
SA-EN28P
Brand: Panasonic Pages: 19
Panasonic SA-H82 Operating Instructions Manual preview
SA-H82
Brand: Panasonic Pages: 40
Panasonic SA-HD52 Operating Instructions Manual preview
SA-HD52
Brand: Panasonic Pages: 42

Brands by name

Popular brands

Load more brands