manualshive.com logo in svg

Yealink VC110, Administrator'S Manual

The Yealink VC110 is an advanced video conferencing system that offers seamless communication and collaboration. To get the most out of this powerful device, you can easily download the user manual for free from our website, ensuring a smooth user experience and optimal utilization of its features.

Share
Download
background image

Configuring Call Preferences

 

125 

Codec 

Algorithm 

Bit Rate 

Sample Rate 

Reference 

G.722.1c

 

24 Kbps

 

32 Ksps

 

RFC 5577

 

G.722.1

 

G.722.1

 

24 Kbps

 

16 or 32 Ksps

 

RFC 5577

 

G722 

G.722 

64 Kbps 

16 Ksps 

RFC 3551 

PCMU 

G.711 

64 Kbps 

8 Ksps 

RFC 3551 

PCMA 

G.711 

64 Kbps 

8 Ksps 

RFC 3551 

Audio codecs parameters on the endpoint are described below: 

Parameter 

Description 

Configuration Method 

Enable Codecs 

Specifies the enabled audio 
codecs for the endpoint to use. 

Note: All support audio codecs 
are enabled on the endpoint by 
default. 

Web User Interface 

Disable Codecs 

Specifies the disabled audio 
codecs for the endpoint not to 
use. 

Web User Interface 

Special audio 

codec byte 

sequence 

Enables or disables the special 
audio codec byte sequence. 

Note: Different devices have 
different definition about how 
some Codecs are stored 
(Big-endian or little-endian), 
which may lead to the audio 
incompatibility problems 
between Yealink and certain 
devices. You can enable the 
special audio codec byte 
sequence feature to solve these 
incompatibility problems. 

Web User Interface 

To configure audio codecs via web user interface: 

1.

 

Click on Account->Codec. 

2.

 

Select the desired codec from the Disable Codecs or the Enable Codecs column. 

3.

 

Click          or          to disable or enable the selected codec. 

4.

 

Select the desired audio codec from the Enable Codecs column, and click          or         
to adjust the priority of the selected audio codecs. 

 

 

Summary of Contents for VC110













































































































































































































































































Reviews:

No comments

Related manuals for VC110

Danfoss ECL Comfort 110 Mounting Manual preview
ECL Comfort 110
Brand: Danfoss Pages: 8
Danfoss AFQM Operating Manual preview
AFQM
Brand: Danfoss Pages: 16
SainSmart Genmitsu User Manual preview
Genmitsu
Brand: SainSmart Pages: 49
Magnavox MM444BT Owner'S Manual preview
MM444BT
Brand: Magnavox Pages: 23
Avaya B109 User Manual preview
B109
Brand: Avaya Pages: 21
Steren BAF-515 Instruction Manual preview
BAF-515
Brand: Steren Pages: 31
Chamberlain GAROG TST WS Series Operational Description preview
GAROG TST WS Series
Brand: Chamberlain Pages: 17
Lenze SMVector Reference Manual preview
SMVector
Brand: Lenze Pages: 76
Advanced Native Technologies iROLLER 10 User Manual preview
iROLLER 10
Brand: Advanced Native Technologies Pages: 29
Naish Torque 2 + i3 50 User Manual preview
Torque 2 + i3 50
Brand: Naish Pages: 18
Philips MZ7/37 Specifications preview
MZ7/37
Brand: Philips Pages: 2
Philips MZ-33 Specifications preview
MZ-33
Brand: Philips Pages: 2
Philips MCM704D Specifications preview
MCM704D
Brand: Philips Pages: 3
Philips MCM390 Specification Sheet preview
MCM390
Brand: Philips Pages: 2
Philips MCM330 Brochure & Specs preview
MCM330
Brand: Philips Pages: 3
Philips MCM330 Specifications preview
MCM330
Brand: Philips Pages: 3
Philips MCM280D Quick Start Manual preview
MCM280D
Brand: Philips Pages: 2
Philips MCM279 Specifications preview
MCM279
Brand: Philips Pages: 3

Brands by name

Popular brands

Load more brands