manualshive.com logo in svg

Yealink VC110, Administrator'S Manual

The Yealink VC110 is an advanced video conferencing system that offers seamless communication and collaboration. To get the most out of this powerful device, you can easily download the user manual for free from our website, ensuring a smooth user experience and optimal utilization of its features.

Share
Download
background image

Configuring Endpoint Settings

 

175 

To configure camera settings via the remote control: 

1.

 

Select Menu->Video & Audio->Camera General Settings. 

2.

 

Configure the camera settings. 

3.

 

Press the Save soft key to accept the change. 

Local video is displayed on the display device of the far site during a call. For the best 
view, you can enable the Far Control of Near Camera feature to allow the far site to 
control the focus and angle of the local camera. You can also specify whether the far 
site is allowed to store and use the local camera presets. 

Far control of the near camera parameters are described below. 

Parameter 

Description 

Configuration Method 

Not FECC in 

call(0~300s) 

Configures the duration time (in 
seconds) when far site cannot 
control the local camera during a 
call. 

Default: 15 

If it is set to 15, the far site is not 
allowed to control the local 
camera in the first 15 seconds of 
the call. 

Web User Interface 

Far Control Near 

Camera 

Enables or disables the far site to 
control the near site camera. 

Default: Enabled 

Remote Control 

Web User Interface 

Far Set of Camera 

Presets 

Enables or disables the far site to 
store the camera presets. 

Default: Disabled 

Remote Control 

Web User Interface 

Far Move to 

Camera Presets 

Enables or disables the far site to 
use the camera presets. 

Default: Disabled 

Remote Control 

Web User Interface 

To configure far-end camera control via web user interface: 

1.

 

Click on Setting->Video & Audio. 

2.

 

Enter the desired time in the Not FECC in call(0~300s) field. 

3.

 

Select the desired values from the pull-down lists of Far Control Near Camera. 

4.

 

Select the desired values from the pull-down lists of Far Set of Camera Presets. 

 

 

Summary of Contents for VC110













































































































































































































































































Reviews:

No comments

Related manuals for VC110

3Com REMOTE ACCESS SYSTEM 1500 Getting Started Manual preview
REMOTE ACCESS SYSTEM 1500
Brand: 3Com Pages: 62
Onn ONA17AA015 Product Manual preview
ONA17AA015
Brand: Onn Pages: 11
Simplex F18804 Installation Instructions Operating Instructions preview
F18804
Brand: Simplex Pages: 40
Denver CUT-301 Instruction Manual preview
CUT-301
Brand: Denver Pages: 12
Ziton ZPR485-3 Installation Manual preview
ZPR485-3
Brand: Ziton Pages: 2
SoundMax SM- MSD11 Instruction Manual preview
SM- MSD11
Brand: SoundMax Pages: 43
Tormatic HA MS 230V Assembly And Operating Instructions Manual preview
HA MS 230V
Brand: Tormatic Pages: 66
Qtx PPA72 User Manual preview
PPA72
Brand: Qtx Pages: 5
Resolution RE928X Manual preview
RE928X
Brand: Resolution Pages: 5
Jazz JZ20-T10 User Manual preview
JZ20-T10
Brand: Jazz Pages: 12
MB QUART MBQ-POD Manual preview
MBQ-POD
Brand: MB QUART Pages: 12
AAD PL-100 Owner'S Information preview
PL-100
Brand: AAD Pages: 8
Hitachi HPS809E Instruction Manual preview
HPS809E
Brand: Hitachi Pages: 14
Hitachi AXM949E Quick Start Manual preview
AXM949E
Brand: Hitachi Pages: 4
Hitachi AXM846E Quick Start Manual preview
AXM846E
Brand: Hitachi Pages: 4
Hitachi CX-V3 Instruction Manual preview
CX-V3
Brand: Hitachi Pages: 28
Hitachi AXM845E Instruction Manual preview
AXM845E
Brand: Hitachi Pages: 32
Hitachi AXM950E Instruction Manual preview
AXM950E
Brand: Hitachi Pages: 40

Brands by name

Popular brands

Load more brands