manualshive.com logo in svg

Yealink VC110, Administrator'S Manual

The Yealink VC110 is an advanced video conferencing system that offers seamless communication and collaboration. To get the most out of this powerful device, you can easily download the user manual for free from our website, ensuring a smooth user experience and optimal utilization of its features.

Share
Download
background image

Administrator‘s Guide for Yealink VC110 Video Conferencing Endpoint 

228 

Parameter 

Description 

Configuration Method 

reboot to make the change take 
effect. 

Port 

Specifies the SNMP port. 

Valid Values: 1-65535 

Default: 161 

Note: If you change this 
parameter, the endpoint will 
reboot to make the change take 
effect. 

Web User Interface 

Trusted Address 

Configures IP address(es) or 
domain name of the trusted 
SNMP server. 

Multiple IP addresses or domain 
names should be separated by 
spaces. 

Note: If it is left blank, the 
endpoint accepts and handles 
GET requests from any SNMP 
server. 

If you change this parameter, the 
endpoint will reboot to make the 
change take effect. 

Web User Interface 

To configure SNMP via web user interface: 

1.

 

Click on Network->Advanced. 

2.

 

In the SNMP block, select Enabled from the pull-down list of Active. 

3.

 

Enter the SNMP port in the Port field. 

4.

 

Enter the IP address or domain name of the SNMP server in the Trusted Address 
field. 

 

 

Summary of Contents for VC110













































































































































































































































































Reviews:

No comments

Related manuals for VC110

W. A. Production Sphere Comp Manual preview
Sphere Comp
Brand: W. A. Production Pages: 5
TANDBERG Videoconference System Quick Start Manual preview
Videoconference System
Brand: TANDBERG Pages: 10
T-audio LX200T User Manual preview
LX200T
Brand: T-audio Pages: 2
Zonex DigiTract 4-2 Installation Manual preview
DigiTract 4-2
Brand: Zonex Pages: 28
SALUPO MULTIPLUS 2 Instruction And Installation Manual preview
MULTIPLUS 2
Brand: SALUPO Pages: 22
Polycom Soundpoint IP 301 Quick Start Manual preview
Soundpoint IP 301
Brand: Polycom Pages: 4
Valcom Syn-Apps VIP-801A-SA Quick Manual preview
Syn-Apps VIP-801A-SA
Brand: Valcom Pages: 2
Polycom CX 200 Quick Start Manual preview
CX 200
Brand: Polycom Pages: 4
Grandstream Networks UCM6304 Quick Installation Manual preview
UCM6304
Brand: Grandstream Networks Pages: 20
Nakamichi NA80 Instruction Manual preview
NA80
Brand: Nakamichi Pages: 11
Panasonic SC-UA4 Operating Instructions Manual preview
SC-UA4
Brand: Panasonic Pages: 68
Panasonic SC-PM251 Operating Instructions Manual preview
SC-PM251
Brand: Panasonic Pages: 18
Samsung MM-77 Service Manual preview
MM-77
Brand: Samsung Pages: 69
Yamaha MusicCast 200 TSX-N237 Brochure preview
MusicCast 200 TSX-N237
Brand: Yamaha Pages: 44
Lenze L-force PROFINET E94AYCER Mounting Instructions preview
L-force PROFINET E94AYCER
Brand: Lenze Pages: 114
Philips FW-C90 Specifications preview
FW-C90
Brand: Philips Pages: 2
Philips FW-C870 Specifications preview
FW-C870
Brand: Philips Pages: 2
Philips FW-C85/18 Specifications preview
FW-C85/18
Brand: Philips Pages: 2

Brands by name

Popular brands

Load more brands