manualshive.com logo in svg

Yealink VC110, Administrator'S Manual

The Yealink VC110 is an advanced video conferencing system that offers seamless communication and collaboration. To get the most out of this powerful device, you can easily download the user manual for free from our website, ensuring a smooth user experience and optimal utilization of its features.

Share
Download
background image

Administrator‘s Guide for Yealink VC110 Video Conferencing Endpoint 

44 

You can choose to mount the VC110 all-in-one unit on your TV or a wall, depending on 
your actual needs. 

a)

 

Mounting the VC110 all-in-one unit on a TV 

When the thickness of your TV is between 35-120 mm, you can mount the VC110 
all-in-one unit on your TV. 

 

Do the following: 

1.

 

Lock the VC110 all-in-one unit to the L-bracket.   

2.

 

Remove the protection of the Velcro. 

3.

 

Put the L-bracket on the top of the TV.   

4.

 

Make sure the back of the TV is clean, and then adjust the bracket to ensure close 
adhesion to the back of the TV with Velcro. 

b)

 

Mounting the VC110 all-in-one unit on a wall 

You can also mount the VC110 all-in-one unit on a wall. The recommended height for 
VC110 all-in-one unit positioning is 1.5m-1.8m above the ground. 

Do the following: 

 

1.

 

Punch holes into the wall and then insert the expansion bolts. 

Summary of Contents for VC110













































































































































































































































































Reviews:

No comments

Related manuals for VC110

Radionics D9000 Series Installation And Troubleshooting Quick Reference preview
D9000 Series
Brand: Radionics Pages: 14
Colorbeam ORBIT TP User Manual preview
ORBIT TP
Brand: Colorbeam Pages: 12
heat-timer MPCQ Platinum Installation And Operation Instructions For preview
MPCQ Platinum
Brand: heat-timer Pages: 40
DINA Safeline DNSL-IO2 Original Instruction Manual preview
Safeline DNSL-IO2
Brand: DINA Pages: 28
DAEWOO ELECTRONICS AMI-926LM/RM Service Manual preview
AMI-926LM/RM
Brand: DAEWOO ELECTRONICS Pages: 34
Mircom FX-MNS-6000 Installation And Operation Manual preview
FX-MNS-6000
Brand: Mircom Pages: 149
VADDIO GroupSTATION Installation And User Manual preview
GroupSTATION
Brand: VADDIO Pages: 40
U-Prox HUB LTE User Manual preview
HUB LTE
Brand: U-Prox Pages: 3
SOUNDMASTER NR995 Manual preview
NR995
Brand: SOUNDMASTER Pages: 110
Binsfeld TorqueTrak Revolution Installation Manual preview
TorqueTrak Revolution
Brand: Binsfeld Pages: 2
Cisco Linksys DMC250 Quick Installation Manual preview
Linksys DMC250
Brand: Cisco Pages: 32
Cisco DMC350 Quick Installation Manual preview
DMC350
Brand: Cisco Pages: 64
ARRI SkyLink User Manual preview
SkyLink
Brand: ARRI Pages: 20
Sharp SD-CX1W(BL) Service Manual preview
SD-CX1W(BL)
Brand: Sharp Pages: 116
Sven SPS-866 Operation Manual preview
SPS-866
Brand: Sven Pages: 12
Svarog 105 PLASMA CNC Operating Manual preview
105 PLASMA CNC
Brand: Svarog Pages: 30
Clas Ohlson 18-8155 Manual preview
18-8155
Brand: Clas Ohlson Pages: 40
APART MASK4C(T) Instruction Manual preview
MASK4C(T)
Brand: APART Pages: 24

Brands by name

Popular brands

Load more brands