manualshive.com logo in svg

Yealink VC110, Administrator'S Manual

The Yealink VC110 is an advanced video conferencing system that offers seamless communication and collaboration. To get the most out of this powerful device, you can easily download the user manual for free from our website, ensuring a smooth user experience and optimal utilization of its features.

Share
Download
background image

Configuring Call Preferences

 

129 

2.

 

Select the desired value from the pull-down list of Call Protocol. 

 

3.

 

Click Confirm to accept the change. 

To configure call protocol via the remote control: 

1.

 

Select Menu->Call Features ->Call Protocol. 

2.

 

Select the desired value from the pull-down list of Call Protocol. 

3.

 

Press the Save soft key to accept the change. 

Do not Disturb allows the endpoint to reject all incoming calls automatically. You can 
activate the DND mode for the endpoint when it is idle, and the DND mode will be 
deactivated after the endpoint places a call. You can also activate the DND mode for 
the endpoint during a call, and the DND mode will be deactivated after the endpoint 
ends the call. 

The DND parameter on the endpoint is described below: 

Parameter 

Description 

Configuration Method 

DND 

Enables or disables DND mode 
on the endpoint. 

Default: Disabled 

Remote Control 

Web User Interface 

To configure DND via web user interface: 

1.

 

Click on Setting->Call Features. 

 

 

Summary of Contents for VC110













































































































































































































































































Reviews:

No comments

Related manuals for VC110

E-Mu 1616 PCI Manual preview
1616 PCI
Brand: E-Mu Pages: 72
E-Mu 1212M Tutorials Manual preview
1212M
Brand: E-Mu Pages: 44
Balboa BP600 Tech Sheet preview
BP600
Brand: Balboa Pages: 23
auna multimedia 10008845 Manual preview
10008845
Brand: auna multimedia Pages: 30
Parker 2003-EC-00 Technical Manual preview
2003-EC-00
Brand: Parker Pages: 58
Grandstream Networks GAC2570 User Manual preview
GAC2570
Brand: Grandstream Networks Pages: 177
Medion P64026 LIFE User Manual preview
P64026 LIFE
Brand: Medion Pages: 122
Danfoss DHP-R 7Ua User Manual preview
DHP-R 7Ua
Brand: Danfoss Pages: 44
Grundig Varixx UMS 4401 SPCD Manual preview
Varixx UMS 4401 SPCD
Brand: Grundig Pages: 47
Belson BSA-1520MP3 Service Manual preview
BSA-1520MP3
Brand: Belson Pages: 34
iRobot Ava 500 Remote User Manual preview
Ava 500
Brand: iRobot Pages: 7
Listen Technologies Audio Everywhere Advanced Manual preview
Audio Everywhere
Brand: Listen Technologies Pages: 2
Sonoro MEISTERSTUCK SO-610 Operating Manual preview
MEISTERSTUCK SO-610
Brand: Sonoro Pages: 334
Vicon NOVA V1400 Programming Manual preview
NOVA V1400
Brand: Vicon Pages: 91
Boss Audio Systems BASS800 User Manual preview
BASS800
Brand: Boss Audio Systems Pages: 13
Philips FW-C38 Specifications preview
FW-C38
Brand: Philips Pages: 2
Aastra 5370 User Manual preview
5370
Brand: Aastra Pages: 134
Sanyo DC-DA1400M Instruction Manual preview
DC-DA1400M
Brand: Sanyo Pages: 12

Brands by name

Popular brands

Load more brands