URAL Motorcycles 4320M Operation Manual Download Page 57 | Manualshive

Page: 57 / 321

URAL Motorcycles 4320M Operation Manual Download Page 57

56

1,2-bolts; 3-side engine support; 4-rear engine support; 5-lower engine front support bracket; 6-pad; 7-
upper engine front support bracket

Figure 42-Power Unit Suspension

4.1.6 Engine Idle Adjustment

Engine idle adjustment allows changing engine rpm for the trucks with YAMZ-536 en-

gines in the range from 700 to 1400 rmp at a pitch of 50-100 rpm, and saving the set rpm (up to
1000 rpm) in the engine electronic control unit memory.

To actuate engine idle adjustment mode, press and hold switch key 6 (see figure 32) for

about 5 seconds. When this mode is actuated engine rpm become equal to 700 rpm, if the acceler-
ator pedal is not pressed. Idle rpm can be increased/decreased by clicking the switch 4, one click
changes rpm by 50 (100) rpm in the pre-set range. After each click switch 4 should return to neu-
tral position.

«
...
55
56
57
58
59
...
»

Summary of Contents for 4320M


































































































































































































































































































































Reviews:

No comments