manualshive.com logo in svg

URAL Motorcycles 4320M, Operation Manual, Page: 166 / 321

Share
Download
URAL Motorcycles 4320M Operation Manual Download Page 166

 

The  shock  absorber  adjustment  in  four  positions  depending  on  the  road  surface.  When 

lifting the button 7 up, suspension stiffness increases, when pushing down – decreases. 

When lifting the lever up, the seat rises, when pushing down - decreases. When the but-

ton 6 is pushed, it is fixed in the chosen position.  

Upon  fixation  of  the  lifted  button  5,  the  seat  quickly  decreases  in  the  lower  position. 

When pushing the button down – the seat automatically rises and fixes in the position, chosen by 
the button 7. 

DRIVING WITH THE LIFTED BUTTON 5 IS FORBIDDEN!

 

ALWAYS  DECREASE  THE  SEAT  WITH  THIS  BUTTON  UPON  EVERY 

TRUCK LEAVING! 

When  lifting  the  lever  4  up,  the  back  is  unlocked,  declines  forward  due  to  the  spring, 

when decreasing - gradually fixed in the chosen position.  

The seat belt buckle 3 fixes the belt buckle. 
To choose the height, the head cushion 2 has four fixing positions at intervals of 20 mm. 
Control organs of the passenger's seat are located on the right side. 

When driving in the truck, the driver and passengers shall fasten their safety belts.

 

Safety  belts are the  effective protective mean of the driver  and passengers from severe 

consequences  of  the  road  vehicle  accident.  To  fasten  the  seatbelt,  it  is  necessary  smoothly  to 
stretch it out, taking the  belt tongue,  and pull the tongue 2 in  accordance  with figure 130 in the 
lock until its clicking position, not allowing ribbons to twist. Make sure, that the lower belt ribbon 
tightly  adjoins  hips  -  the  lower  belt  ribbon  shall  not  go  around  the  waist.  To  unfasten  the  belt, 
push the red button of the lock, the belt will automatically return in the initial position. 

 

 

 

If  straps  are  stained,  clean  them  with  mild  soap.  Ironing  of  straps  is  not  allowed,  Belt 

shall be replaced with the new one, if it underwent critical load during the road vehicle accident or 
has buffies, disruptions and other damages. 

4.7.1.2 Cab of the conventional cabin truck 

is the three-seater, located behind the en-

gine, equipped with conventional cabin truck heat and sound insulation, seats for drivers and pas-
sengers, the ventilation system, the central and local heating of windshields, sunscreens, the wind 
shield  wiper,  the  windshield  washer,  rear  view  mirrors  from  right  and  left  sides,  the  wide-angle 
mirror and the side view mirror. 

 
 
 
 

 
 

 

162

1-Lock; 2-tongue 
 

Figure 130 - Fastening of the safety belt 

 

Summary of Contents for 4320M


































































































































































































































































































































Reviews:

No comments