TYM T194 Manual Download Page 94

Page: 94 / 169

4 - 4

OPERATION

5. sTARTINg Off, shIfTINg

ANd dRIvINg

sTARTINg Off

①

Lift an implement.

②

Place the main shift lever, range

shift lever and shuttle shift lever

into the desired positions.

③

Depress the brake pedal to

release the parking brake.

►

The driving speed in the reverse

direction is almost the same to

the speed in the forward direc

tion. Make sure to check the

surroundings carefully when

driving backward.
Especially, never drive back

wards with the range shift lever

in the position H. The driving

speed becomes faster and it

can cause an accident.

•

wARNINg

6. sTOPPINg ANd PARkINg

①

Operate the throttle lever to set

the engine at a low speed.

②

Release the forward driving (HST

type) and accelerator (mechani

cal) pedals slowly. Depress the

brake pedals for abrupt braking.

③

When the vehicle is completely

stopped, set the shift lever in the

neutral position.

④

Apply the parking brake.

⑤

If an implement is attached to the

vehicle, lower it.

TK0301A

Make sure to keep the following in

structions for the initial 50-hour use.

(1) Avoid abrupt starting and abrupt

stopping.

(2) Do not use excessive speed or

load.

(3) Drive the Ride on lawnmower

only when the engine is suffi

ciently warm.

(4) Do not idle the engine at the

maximum speed.

(5) Check each part and change oil

and fluid after 50-hour use.

(6) Refer to the section Maintenance

for adding and changing engine

oil.

4. RuNNINg-IN PERIOd

T194(K0) RIDE ON LAWNMOWER-영문-044 4

2018-06-27 오후 6:12:02

Summary of Contents for T194










































































































































































Search results

Summary of Contents for T194

Reviews:

Related manuals for T194

Brands by name

Popular brands

TYM T194, Manual

Search results

Summary of Contents for T194

Reviews:

Related manuals for T194

Brands by name

Popular brands