manualshive.com logo in svg

TYM T194, Manual

Share
Download
TYM T194 Manual Download Page 46

2 - 

DESCRIPTION OF RIDE ON lawNmOwER CONTROlS

(4) PTO indicator

This  comes  on  while  the  PTO 
shaft is rotating.

PTO indicator

Fuel level warning lamp

(3) Fuel level warning lamp

If  keeping  driving  with  the 
n e e d l e  o f  t h e  f u e l  g a u g e 
pointing at 'E,' the warning lamp 
comes on which means there is 
only  approx.  5  liters  of  fuel  left 
in the tank.

Low beam indicator

Left turn signal indicator

(1) Left turn signal indicator

This  lamp  is  used  to  indicate 
the  intended  turning  direction  of 
the  driver.  When  pulling  down 
the  turn  signal  switch,  the  left 
turn  signal  lamp  blinks.  When 
pushing  up  the  turn  signal 
switch,  the  right  turn  signal 
lamp  blinks. These  lamps  are 
operated  when  pressing  the 
hazard  warning  lamp  switch  as 
well.

(2) Low beam indicator

This  comes  on  when  the  low 
beam is turned on.

T194(K0) RIDE ON LAWNMOWER-영문-028   8

2018-07-03   오후 3:49:13

Summary of Contents for T194










































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands