manualshive.com logo in svg

TYM T194, Manual

Share
Download
TYM T194 Manual Download Page 113

6 - 1

Maintenance and service

436

greasing pOints

For general greasing points, refer 

to the fuel, oil and fluid specification 

chart. (See page 5-.)
However, add grease before work 

if the Ride on lawnmower is to be 

used in a wet field.

greasing brake arM  

Remove  the  rubber  caps  on  the 

floor and dash panel to access to 

the grease nipple.
Add grease with the supplied grease 

gun.

►

►

8. greasing

9. checking hOses

Rubber parts, such as the fuel hose 

and radiator hose, are aged by time 

even when the Ride on lawnmower 

is not in use. Therefore, such parts 

should be replaced with their tight-

ening bands every  years or when 

they are damaged.

If  any  fuel  hose  is  damaged, 

fuel leaks and it can catch fire. 

Make  sure  to  check  the  fuel 

hose and take a necessary ac-

tion.

•

Warning

T194(K0) RIDE ON LAWNMOWER-영문-0613   13

2018-08-13   오후 2:30:53

Summary of Contents for T194










































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands