TYM T194 Manual Download Page 143

Page: 143 / 169

9 -

Safety Standard for farm work

439

7. rIde on lawnmower



Manage PTO

- Stop PTO before stopping the engine.

- Do not remove the PTO protective cover or protec-

tive panel for operating machine.

- Do not use PTO adaptor in order to extend the POT

coupler or universal joint to outside of PTO protec-

tive cover.



To repair, secure the wheel width, or changing the

wheel under either Ride on lawnmower or trailer, with

the Ride on lawnmower or trailer raised, choke the

wheels that are on the ground.



Do not use hydraulic jack for operating machine or

Ride on lawnmower. Instead, use block or stand.



Safety frame

- Do neither weld nor drill a hole on the attached safe-

ty frame. Also do not modify it.

- Replace the damaged safety frame with a new one.

- If the safety frame was removed for specialized

work, restore it immediately.



Be careful to touch dangerous area such as power

transmission gear, rotating unit, etc. Put on a protec-

tive cover.



Do neither modify nor remove the safety device.

T194(K0) RIDE ON LAWNMOWER-영문-097 7

2018-07-03 오후 4:14:43

Summary of Contents for T194










































































































































































Search results

Summary of Contents for T194

Reviews:

Related manuals for T194

Brands by name

Popular brands

TYM T194, Manual

Search results

Summary of Contents for T194

Reviews:

Related manuals for T194

Brands by name

Popular brands