TYM T194 Manual Download Page 81

Page: 81 / 169

OPERATiOn

3 - 1

TK0311A

(L)

Front Link

TK031A

Front Bracket

Groove

FROnT Link

1. Hook the front link to the front brack-

et groove as shown in the figure.

►

Make sure the position (L) of the

front link is 1st or nd hole.

nOTE

TK0313A

U pin

Lever Fulcrum

Front Link

Bracket

Front Lever

Lever Fulcrum

Groove

Front Link

MOUnTinG FROnT Link

1. Position the front lever to the front

link bracket.

. Pull and lock the U pin. Then lower

the front lever.

3. Hook the front link to the lever ful-

crum, and lift the front lever.

4. Release the U pin to lock the front

lever.

►

When hooking the front link to the

lever fulcrum, normal position of

the lever fulcrum groove is open

to downward.

nOTE

Check that the front lever is

locked securely with the L pin.

•

CAUTiOn

T194(K0) RIDE ON LAWNMOWER-영문-0321 21

2018-09-11 오후 5:27:34

Summary of Contents for T194










































































































































































Search results

Summary of Contents for T194

Reviews:

Related manuals for T194

Brands by name

Popular brands

TYM T194, Manual

Search results

Summary of Contents for T194

Reviews:

Related manuals for T194

Brands by name

Popular brands