TYM T194 Manual Download

Page: 47 / 169

2 -

DESCRIPTION OF RIDE ON lawNmOwER CONTROlS

(8) Engine oil pressure warning lamp

This is illuminated when the

engine oil pressure or oil
amount is insufficient during
driving.

Engine oil pressure warning lamp

Charge warning lamp

Preheat indicator

(6) Preheat indicator

This comes on while the engine
preheating function is activated.

It goes

off as soon as preheating is completed.

Parking indicator

When the oil pressure warning

lamp comes on, this indicates

malfunction of the lubrication

system. Check the engine oil

immediately and have your ve-

hicle serviced by your workshop

as necessary.

•

NOTE

(7) Charge warning lamp

This comes on when the main

switch is turned to the "ON"
position, and goes off as soon
as the engine is started.

If the charge warning lamp

comes on while driving, the bat-

tery is not properly charged.

Therefore, turn off any unneces-

sary electrical devices and have

your vehicle checked by your

workshop immediately.

•

NOTE

(5) Parking indicator

T h i s c o m e s o n w h e n t h e

parking brake is applied.

T194(K0) RIDE ON LAWNMOWER-영문-029 9

2018-07-03 오후 3:49:14

Summary of Contents for T194










































































































































































Search results

Summary of Contents for T194

Reviews:

Related manuals for T194

Brands by name

Popular brands

TYM T194, Manual

Search results

Summary of Contents for T194

Reviews:

Related manuals for T194

Brands by name

Popular brands