TYM T194 Manual Download Page 19

Page: 19 / 169

- 1

SAFeTY PReCAUTIONS

1. Ensure that all mounting and re-

moval of implements is done on

safe flat ground. Ensure no one

is between the Ride on lawn-

mower and implement and do not

get under the implement to avoid

accidental injuries.

2. After mounting the implement, en-

sure that all stabilizers are cor-

rectly adjusted and, where PTO

shafts are used that the shaft is

fitted and secured correctly.

3. Where heavy implements are

used, ensure that the combina-

tion is well balanced or use prop-

er ballast to achieve balance.

4. Before leaving the Ride on lawn-

mower at any time, lower the im-

plement, stop the PTO shaft

where applicable, set the parking

brake and switch off the engine.

5. While operating the implements

with the PTO keep all bystanders

away from any moving parts and

MOUNTING AND ReMOVING IMPLeMeNTS

do not attempt to make adjust-

ments while the machine is run-

ning.

6. Only the driver should ride on

the Ride on lawnmower with the

ROPS frame fitted and with the

seat belt properly fastened.

7. Where young children are pres-

ent, particular care should be

taken and the Ride on lawnmow-

er should not be moved until the

whereabouts of all children is

known.

8. Only trained operators should op-

erate the Ride on lawnmower

and so taking care to ensure that

other workers are not injured. In

particular they should take care

during dusty operations, which

will reduce visibility substantially.

9. Never start the Ride on lawn-

mower unless the transmission

is out of gear, the operator is in

the seat and all round safety has

been checked.

10. Only operate the Ride on lawn-

mower seated in the drivers

seat and never turn or brake

suddenly at high speed as this

can cause a roll-over and seri-

ous injury or death.

11. When traveling on a public road

ensure that the Ride on lawn-

mower and driver both meet all

laws relating to safety and li-

censing. When traveling with

wide implements use red flags

on the extremities and observe

all legal including escort re-

quirements.

12. When operating under adverse

conditions, hilly terrain or on

bad ground adjust the speed of

the Ride on lawnmower to suit

the conditions, safety comes

first. Never drive down hill at

high speed or with the transmis-

sion in neutral. Use of the brak-

ing capacity of the engine as

well as the service brakes.

T194(K0) RIDE ON LAWNMOWER-영문-0119 19

2018-08-13 오후 4:23:17

Summary of Contents for T194










































































































































































Search results

Summary of Contents for T194

Reviews:

Related manuals for T194

Brands by name

Popular brands

TYM T194, Manual

Search results

Summary of Contents for T194

Reviews:

Related manuals for T194

Brands by name

Popular brands