TYM T194 Manual Download Page 88

Page: 88 / 169

3 - 8

OPERATiOn

BLAdE inSTALLATiOn

When reinstalling the blade note ori-

entation, the "wing" must be point-

ing upward the top of the deck.

►

BELT REPLACEMEnT

The mower deck belts should be

replaced every 00 hours of mower

operation, or anytime the belts

shows sign of wear, cracking, or

other damage.
Remove hardware securing the Left/

Right Hand Belt cover to the deck.

►

The Idler Arm with Idler Pulley are

under spring tension. To prevent

possible injury, use caution when

handling the Idler Arm assmbly.

CAUTiOn

Place a "Breaker Bar" in the square

hole provided in the Idler Arm. Care-

fully push the Idler Arm towards the
left hand side, away from discharge

opening to relieve tension from the

belt. Slip the belt off of the Right

hand Spindle Pulley, then carefully

release the Idler Arm.

Remove the belt from the Center

Spindle Pulley.

Remove the belt from the first fixed

Idler Pulley.
Remove the belt from the Left Hand

Spindle Pulley.
Remove the belt from the Idler Arm

Pulley.
Remove the belt from the Gear Box

Pulley.
Remove the belt from the Second

Idler Pulley.
Remove the belt from the deck and

discard.

T194(K0) RIDE ON LAWNMOWER-영문-0328 28

2018-09-11 오후 5:27:46

Summary of Contents for T194










































































































































































Search results

Summary of Contents for T194

Reviews:

Related manuals for T194

Brands by name

Popular brands

TYM T194, Manual

Search results

Summary of Contents for T194

Reviews:

Related manuals for T194

Brands by name

Popular brands