TYM T194 Manual Download Page 15

Page: 15 / 169

- 1

SAFeTY PReCAUTIONS

If you spill acid on yourself;

1. Flush your skin with water.
2. Flush your eyes with water for

10-15 minutes.

Get medical attention immediately.

T72O216A

Do not wear a necktie, scarf or

loose clothing when you work near

moving parts. If these items were to

get caught, severe injury could re-

sult.
Remove rings and other jeweler to

prevent electrical shorts and entan-

glement in moving parts.

SeRVICe RIDe ON LAWN-

MOWeR SAFeLY

1. When working with your Ride on

lawnmowers electrical compo-

nents you must first disconnect

the battery cables.

2. To ensure that there are no acci-

dents from sparks you must first

disconnect the negative battery

cable.

T74O224A

BATTeRY DISCONNeCT

T194(K0) RIDE ON LAWNMOWER-영문-0115 15

2018-08-13 오후 4:23:09

Summary of Contents for T194










































































































































































Search results

Summary of Contents for T194

Reviews:

Related manuals for T194

Brands by name

Popular brands

TYM T194, Manual

Search results

Summary of Contents for T194

Reviews:

Related manuals for T194

Brands by name

Popular brands