TYM T194 Manual Download Page 41

Page: 41 / 169

2 -

DESCRIPTION OF RIDE ON lawNmOwER CONTROlS

T19O108B

OFF

Start

maIN SwITCH

It is used to start and stop the en-

gine.



"OFF" position

The ignition key can be inserted

and removed in this position.

When turning the switch to the

OFF position with the engine

running, the engine is stopped.



"ON" position

The engine is kept running and

the switch is energized in this

position.

►



"STaRT" position

The engine can be started in

this position. When releasing the

key, the switch is returned to the

"ON" position.



"GlOw" position

The engine's combustion chamber

is pre-heated in this position.

T19O109A

TaCHOmETER

It displays the revolution of the en-

gine or PTO shaft per minute.

►

GLOW

T194(K0) RIDE ON LAWNMOWER-영문-023 3

2018-07-03 오후 3:49:03

Summary of Contents for T194










































































































































































Search results

Summary of Contents for T194

Reviews:

Related manuals for T194

Brands by name

Popular brands

TYM T194, Manual

Search results

Summary of Contents for T194

Reviews:

Related manuals for T194

Brands by name

Popular brands