manualshive.com logo in svg

TYM T194, Manual

Share
Download
TYM T194 Manual Download Page 18

    - 1

SAFeTY PReCAUTIONS

1. At least on a daily basis check all 

oil levels. Water level in the radia-

tor and electrolyte level in the bat-

tery and perform services accord-

ing to the service schedule. 

2. Ensure  tire  pressure  are  even 

and the correct pressure for the 

job being done is maintained.

3. Check to ensure that the all con-

trols  and  preventative  mecha-

nisms of the Ride on lawnmower 

and implement work correctly and 

effectively.

4. Ensure that an adequate set of 

the correct tools is available for 

maintenance and minor repairs.

5. Ensure that all service work and 

repairs are carried out on a flat 

area with a concrete or similar 

floor. 

SAFeTY TIPS DURING MAINTeNANCe

  Do  not  carry  out  service  work 

on  a  Ride  on  lawnmower  un-

til it is switched off, and the park-

ing  brake  applied  and  wheels 

choked. 

   Where a Ride on lawnmower is 

started in a confined area, en-

sure that the area is well venti-

lated as exhaust gases are very 

harmful, and can cause death. 

 6. Do not work under raised imple-

ments.

 7. When changing wheels or tires 

ensure  that  a  suitable  wheel 

stand is placed under the axle 

prior to removing the wheel and 

the wheels are chocked.

 8. Where guards or shields need to 

be removed to perform a service 

or repair, ensure that the guard  

or shield is correctly reinstalled 

before starting the Ride on lawn-

mower.

 9. Never refuel near a naked flame 

or with an overheated engine. 

Ensure to turn off Engine before 

refueling.

10. The cooling system operates un-

der pressure, take care when re-

moving the radiator cap on a hot 

engine to prevent being scald-

ed by steam or hot water. Do not 

add water in the radiator when 

the engine is hot. Add water to 

the radiator only after the engine 

cools down completely.

11. To prevent fires keep the Ride 

on lawnmower including the en-

gine clean and free from inflam

-

mable material and well away 

from fuels and other inflammable 

material. 

T194(K0) RIDE ON LAWNMOWER-영문-0118   18

2018-08-13   오후 4:23:16

Summary of Contents for T194










































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands