TYM T194 Manual Download Page 118

Page: 118 / 169

6 - 18

Maintenance and service

11. check and adjust each part

brake pedal play

Depress the pedal lightly with a

hand to check its play.

►

Play

Pressing

divisiOn specified value

Play

11.8 ~ 15. in.

(0 ~ 0 mm)

11.8 ~ 15. in.

(0 ~ 0 mm)

T19O51A

checking and adjust-

ing fan belt

Check and adjust the fan belt's ten-

sion periodically.

①

Unscrew the alternator mounting

bolt slightly and move the alter-

nator to adjust the tension.

②

Check the belt's tension.

Press the middle of the belt with

1. ~ 15. Ib (6 ~ kg) of force.

It is okay when the belt is deflect

ed for 0.8 ~ 0.5 in. ( ~ 9 mm).

►

T5O55B

Mounting bolt

Fan belt

checking and adjust-

ing brake pedal

The brake pedal's play increases as

it is used for an extended period of

time. If its play is excessive, adjust it.

<adjustment>

①

Unscrew the lock nut and turn

the adjusting nut to adjust the

play (left and right).

②

Turning it counterclockwise in-

creases the play while turning it

clockwise decreases the play.

③

After adjustment, tighten the lock

nut firmly.

►

Lock nut

Turn buckle

0.8 ~ 0.5 in.

( ~ 9 mm)

After adjustment, confirm the

operating state.

•

Warning

T194(K0) RIDE ON LAWNMOWER-영문-0618 18

2018-08-13 오후 2:31:11

Summary of Contents for T194










































































































































































Search results

Summary of Contents for T194

Reviews:

Related manuals for T194

Brands by name

Popular brands

TYM T194, Manual

Search results

Summary of Contents for T194

Reviews:

Related manuals for T194

Brands by name

Popular brands