TYM T194 Manual Download

Page: 56 / 169

2 - 1

DESCRIPTION OF RIDE ON lawNmOwER CONTROlS

(3) Folding seatback
The seatback can be folded down

when it is raining or for long-term

storage.

Make sure to wear your seat

belt to protect yourself from a

possible rollover or crash acci-

dent.
Never adjust the seat during

driving.

•

waRNING

T19O127A

PTO

Both of the rear and mid PTO are

provided for variable utility. They

can be engaged simultaneously or

separately at same time.
The engine will not start if PTO

switch is ON position.
The engine will shutoff if the op-

erator leaves the seat with parking

brake released and PTO engaged.

►

To avoid damage of transmis-

sion and implement, do not

engage PTO with the engine

running at high speed.

•

CaUTION

Mid

T19O128B

N
Mid+Rear
N
Rear

T194(K0) RIDE ON LAWNMOWER-영문-0218 18

2018-07-03 오후 3:49:37

Summary of Contents for T194










































































































































































Search results

Summary of Contents for T194

Reviews:

Related manuals for T194

Brands by name

Popular brands

TYM T194, Manual

Search results

Summary of Contents for T194

Reviews:

Related manuals for T194

Brands by name

Popular brands