TYM T194 Manual Download Page 107

Page: 107 / 169

6 -

Maintenance and service

436

(2) changing

①

Unscrew the drain plug on the

lower section of the transmission

to drain contaminated transmis-

sion fluid. Since hot fluid flows

out of the engine first, be careful

not to get burnt.

②

After draining fluid, tighten the

transmission fluid drain plug.

③

Add the specified amount of

the specified transmission fluid

through the filler hole.

If transmission fluid gets on

your skin, it can irritate the skin

and cause a skin condition.

Make sure to clean your skin

with soap and water or hand

cleaner thoroughly.

•

cautiOn

(3) Oil specification

THF 80W
(API GL- Grade, Gear Oil 80W)

Do not add fluid over the upper

limit level.

Check the fluid before starting

the engine or at least in 5 min-

utes after the engine is stopped.
When trying to use new fluid

from a different manufacturer

or fluid with different viscosity,

drain used fluid completely be-

fore adding new fluid.

•

nOte

T9O508A

Upper

limit

Lower

limit

Drain plug

T19O50A

T194(K0) RIDE ON LAWNMOWER-영문-067 7

2018-08-13 오후 2:30:40

Summary of Contents for T194










































































































































































Search results

Summary of Contents for T194

Reviews:

Related manuals for T194

Brands by name

Popular brands

TYM T194, Manual

Search results

Summary of Contents for T194

Reviews:

Related manuals for T194

Brands by name

Popular brands