manualshive.com logo in svg

TYM T194, Manual

Share
Download
TYM T194 Manual Download Page 157

12

 - 

WARRANTY

12

timing gear, and gear case. The warranty period for both the standard limited warranty and the extended limited 
warranty (by duration or operation hours) begins on the date of delivery to the original retail purchaser and is valid 
only until the applicable warranted duration has passed or the operation hours are exceeded, whichever comes 
first.

What is not Covered by this Warranty?

This  warranty  does  not  cover  parts  affected  by  or  damaged  by  any  reason  other  than  defective  materials  or 
workmanship, including, but not limited to, accident, misuse, abuse, "Acts of God," neglect, improper installation, 
improper maintenance, improper storage, the use of unsuitable attachments or parts, the use of contaminated 
fuels,  the  use  of  fuels,  oils,  lubricants,  or  fluids  other  than  those  recommended  in  your YANMAR  Operation 
Manual, unauthorized alterations or modifications, ordinary wear and tear, and rust or corrosion. This warranty 
does  not  cover  the  cost  of  parts  and/or  labor  required  to  perform  normal/scheduled  maintenance  on  your 
YANMAR engine. This warranty does not cover consumable parts such as, but not limited to, filters, belts, hoses, 
fuel injector, lubricants and cleaning fluids. This warranty does not cover the cost of shipping the product to or 
from the warranty repair facility.

Warranty limitations:

The foregoing is YANMAR's only obligation to you and your exclusive remedy for breach of warranty. Failure to 
follow the requirements for submitting a claim under this warranty may result in a waiver of all claims for damages 
and other relief. In no event shall YANMAR or any authorized industrial engine dealer or distributor be liable for 
incidental, special or consequential damages. Such consequential damages may include, but not be limited to, 
loss of revenue, loan payments, cost of rental of substitute equipment, insurance coverage, storage, lodging, 

T194(K0) RIDE ON LAWNMOWER-영문-123   3

2018-06-28   오전 10:28:16

Summary of Contents for T194










































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands