manualshive.com logo in svg

TYM T194, Manual

Share
Download
TYM T194 Manual Download Page 69

OPERATiOn

3 - 9

33

Do not mow when the grass is wet 

or heavy with dew.
Wet grass can build up on the un-

derside  of  the  deck,  creating  an 

imbalance through the blades and 

spindles, causing possible damage 

to the mower deck belt. Wet grass 

also leaves unsightly clumps on the 

lawn.
Should  the  mower  deck  become 

plugged, raise deck, shut off engine, 

set parking brake, and lock the deck 

in the transport position.
Clean the underside of the mower 

deck using a scraper.
Operate the mower only in daylight 

or with good artificial light.

9. MAinTEnAnCE(1)

1.  Protect your eyes- Wear Safety 

Glasses.

.  Never  run  the  Ride  on  Mower 

inside a closed area. Engine ex-

haust fumes can be lethal.

3.  Always engage lift lockouts be-

fore servicing the mower.

4.  Before  performing  any  service 

work,  make  sure  hoists,  floor 

jacks, and jack stands are in good 

working order and properly rated 

to support the Ride on Mower.

5.  Do not work under the Ride on 

Mower unless they are secured 

by a hoist and jack stands.

   Never place any body part un-

derneath equipment or between 

moveable parts even after Ride 

on Mower has been turned off. 

Hydraulic system leak downs, hy-

draulic system failures, mechani-

cal failures, or control lever move-

ment can cause mower and Ride 

on Mower components to drop or 

rotate unexpectedly and cause 

serious injury or death.

  6.  Avoid injury, do not adjust, ser-

vice, clean, or unclog the mower 

when the Ride on Mower engine 

is running.

  7.  Frequently  check  the  mower 

blades. 

     They must be sharp and free of 

nicks, cracks and securely fas-

tened.

  8.  Do  not  handle  mower  blades 

with bare hands. Wear leather 

gloves  or  wrap  blades  in  the 

area Where they will be handled. 

Improper handling may result in 

serious injury.

  9.  Your dealer can supply genuine 

replacement blades. Non-genu-

ine blades may not meet original 

equipment  specifications  and 

may be dangerous if installed.

T194(K0) RIDE ON LAWNMOWER-영문-039   9

2018-09-11   오후 5:27:14

Summary of Contents for T194










































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands