TYM T194 Manual Download Page 5

Page: 5 / 169

SAFeTY PReCAUTIONS

▶

GeNeRAL CONSTRUCTION

The transmission case, Engine and

Front Axle Support are bolted to-

gether to form a rigid unit.

▶

FRONT AxLe & WHeeLS

The 4WD front axle is a center-piv-

ot, reverse Eliot type. The front

wheel drive mechanism is incorpo-

rated as a part of the axle.
The front wheel drive power is taken

off the rear transmission and trans-

mitted to the differential in the front

axle where the power is divided into

right and left and to the respective

final cases.

In the final cases, the transmitted

revolution is reduced by the level

gears to drive the front wheel. The

4WD mechanism with level gears

provides wider steering and greater

durability.

▶

eNGINe

The Ride on lawnmower are fitted

with vertical, Water-cooled 3-cycle

and spherical chamber type YANMAR
ENGINE(3TNV74F-SDKTF2)

▶

TRANSMISSION WITH HST (HY-

DROSTATIC TRANSMISSION)

The Ride on lawnmower is fitted

HST with 2 Range and can be se-

lected Speed range by HIGH-LOW

selector lever.
The Ride on lawnmower has Two

pedals for forward/reverse control .

Ride on lawnmower with Indepen-

dent Power Take Off is fitted with

electro-hydraulic Clutch Assy. The

Mid PTO can be operated both or

separately by a lever.
TYM Ride on lawnmower are pro-

vided with independent disc brakes

operated by two road travel. A foot

brake lever is fitted for parking.

DeSCRIPTION

▶

ReAR AxLe & WHeeLS

This is mounted on ball bearings

and is enclosed in removable hous-

ing which are bolted to the transmis-

sion case. The rim & Disc fitted with

Rear tires are bolted to the outer

flange of Rear Axle.

▶

HYDRAULIC SYSTeM & LINK-

AGeS

TYM

Ride on lawnmower are fitted

with Live (i.e. system is in operation)

independent, very touch of hydraulic

System.

▶

STeeRING

It consists of Hydrostatic Power

steering system, which has a hy-

draulic cylinder and tandem type hy-

draulic pump.

3. DeSCRIPTION

T194(K0) RIDE ON LAWNMOWER-영문-015 5

2018-08-13 오후 4:22:27

Summary of Contents for T194










































































































































































Search results

Summary of Contents for T194

Reviews:

Brands by name

Popular brands

TYM T194, Manual

Search results

Summary of Contents for T194

Reviews:

Brands by name

Popular brands