TYM T194 Manual Download Page 104

Page: 104 / 169

6 -

Maintenance and service

3. inspecting and changing cOOlant

engine cOOlant inspectiOn

and change

(1) inspection

Open the radiator cap and check

that the radiator is filled with cool-

ant up to its filler inlet. If the coolant

amount is insufficient, add more

coolant.

►

Do not open the cap when the

engine is hot. Otherwise, hot

steam can burn you seriously.

Wait until the engine is suffi-

ciently cooled down.

•

Warning

(2) antifreeze

If coolant freezes, the engine can be

damaged.

Clean the radiator thoroughly

before adding antifreeze.

The mixture ratio of antifreeze is

different by manufacturers and

temperature. Refer to the manu-

facturer's manual.

Mix antifreeze with water suffi

ciently before adding it.
Adding antifreeze

If evaporated - Add water for the

reduced amount.

If leaked - Add mixture of anti

freeze and water with the same

mixture ratio.

•

If engine coolant gets on your

skin, it can irritate the skin and

cause a skin condition. Make sure

to clean your skin with soap and

water or hand cleaner thoroughly.

•

cautiOn

cleaning radiatOr and

radiatOr grilles

When working in a grassy field or

working at night, the radiator or

condenser grille may be clogged

by grass, straws or bugs, reducing

cooling performance.
In this case, clean the grille. If dust

is stuck between the fan and tube,

flush the area with clean water.

►

Do not clean the radiator fin with

water jet. It can deform the fin.

•

nOte

Inlet

Radiator

Check hoses

T19O50A

Radiator grill

T194(K0) RIDE ON LAWNMOWER-영문-064 4

2018-08-13 오후 2:30:31

Summary of Contents for T194










































































































































































Search results

Summary of Contents for T194

Reviews:

Related manuals for T194

Brands by name

Popular brands

TYM T194, Manual

Search results

Summary of Contents for T194

Reviews:

Related manuals for T194

Brands by name

Popular brands