TYM T194 Manual Download Page 159 | Manualshive

Page: 159 / 169

background image

12

-

WARRANTY

12

■

eMIssION sYsTeM WARRANTY

YANMAR CO., lTD. eMIssION CONTROl sYsTeM WARRANTY- UsA ONlY

Your Warranty Rights and Obligations:

The  California Air  Resources  Board  (CARB),  the  United  State  Environmental  Protection Agency  (EPA)  and
YANMAR  CO.,  LTD.  hereafter  referred  to  as YANMAR,  are  pleased  to  explain  the  emission  control  system
warranty  on  your  industrial  compression-ignition  engine.  In  California,  model  year 000  or  later  off-road
compression-ignition engines must be designed, built and equipped to meet the State's stringent anti-smog In
all states, 1998 and later non-road compression-ignition engines must be designed, built and equipped to meet
the United States EPA emissions standards. YANMAR must warrant the emission control system on your engine
for the periods of time listed below provided there has been no abuse, neglect or improper maintenance of your
engine.
Your emission control system may include parts such as the fuel injection system, the air induction system, the
electronic control system, EGR (Exhaust Gas Recirculation) system and the diesel particulate filter system. Also
included may be hoses, belts, connectors and other emission-related assemblies.
Where  a  warrantable  condition  exists, YANMAR  will  repair  your  off-road  compression-ignition  engine  at  no
charge to you including diagnosis, parts and labor.

T194(K0) RIDE ON LAWNMOWER-영문-125 5

2018-06-28 오전 10:28:17

«
...
157
158
159
160
161
...
»

Summary of Contents for T194










































































































































































Reviews:

No comments

Related manuals for T194

Brand: Baroness Pages: 199

Brand: Baroness Pages: 5

Brand: Poulan Pro Pages: 48

Brand: Toro Pages: 60

Brand: Spearhead Pages: 64

Brand: Yard Machines Pages: 72

Brand: Bush Hog Pages: 1

Brand: Lastec Pages: 51

Brand: Toro Pages: 12

Brand: Snapper Pages: 12

Brand: MTD Pages: 28

28HP Tank 53AB5JEZ630

Brand: Cub Cadet Pages: 36

Brand: Zoef Robot Pages: 54

Brand: MTI Pages: 17

Brand: VITO GARDEN Pages: 40

Brand: Cub Cadet Pages: 9

Brand: Tramontina Pages: 36

Brand: FLORABEST Pages: 90

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands