TYM T194 Manual Download

Page: 82 / 169

3 -

OPERATiOn

16. MOWER AdJUSTMEnT

Park the Ride on Mower on a

firm, flat and level surface and

set the parking brake.
Stop the engine, remove the

key, and allow the blades to

stop before making adjust-

ments.
Wear heavy gloves or wrap end

of blade with a rag when you

handle blades.
Before starting the engine, set

the PTO clutch lever to off posi-

tion and range gear shift lever

to the neutral position.

•

CAUTiOn

TK0314A

Adjustment Point

Bolt
Lock

Nut

TK0315A

9mm

± 3mm

TK0316A

Adjustment

Point

Check Point

Bolt

Lock

Nut

Link

AdJUSTinG MOWER Link

1. Tire pressure must be correct.
. Move the hydraulic control lever

rearward to raise the mower to

the highest position.

3. Stop the engine and remove the

key.

4. Tighten the bolt and nut clear-

ance 9mm - Assembly Lift link

►

Bolt to Lock nut

clearance

Factory spec.

9mm ± 3mm

0 to 0.5 mm

(0 to 0.01 in.)

※

Set the mower height by adjust-

ing the bolt (initial setting posi-

tion)

※

Bolt to Lock nut clearance

: 9mm ± 3mm

T194(K0) RIDE ON LAWNMOWER-영문-0322 22

2018-09-11 오후 5:27:36

Summary of Contents for T194










































































































































































Search results

Summary of Contents for T194

Reviews:

Related manuals for T194

Brands by name

Popular brands

TYM T194, Manual

Search results

Summary of Contents for T194

Reviews:

Related manuals for T194

Brands by name

Popular brands